Ultraflex Power A Mark II Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 36

Ultraflex Power A Mark II Скачать руководство пользователя страница 16

Owner's manual

ULTRAFLEX

page 16

of 36-

POWER A MK2

E

NG

L

ISH

The HIGH-IDLE mode allows the user to increase the engine idle speed.

To enable this mode the following conditions must be met:

- The station must be enabled.

- The DOCKING mode must not be enabled.

- There must be no failures that could prevent this mode from being enabled.

To enable the HIGH-IDLE mode just press the proper
key on the user interface.

The proper red LED will light up indicating that the
HIGH-IDLE mode is on.

In the engine acceleration curve the high idle value
is set as the idle speed.

To disable the HIGH-IDLE mode, press the proper key on the user interface: the HIGH-IDLE red LED switches
off when this mode is disabled.

In a twin-engine system the HIGH-IDLE mode can be enabled on one engine
only. In this case the HIGH-IDLE red LED will blink.

The HIGH-IDLE mode is disabled when changing the control station.

2.4.3 HIGH-IDLE mode

WARNING



«
...
14
15
16
17
18
...
»

Содержание Power A Mark II





































Отзывы:

Нет отзывов