Ultraflex Power A Mark II Скачать руководство пользователя страница 24

Страница: 24 / 36

Owner's manual

ULTRAFLEX

page 24

of 36-

POWER A MK2

ISH

3.3 Shift unit

No.

Alarm code

Meaning

Solution

Miss acc msg

port

The system has detected the lack of

CAN message of the port throttle

Check the CAN bus connection or

the power cord of the unit

controlling the throttle.

Miss disp msg

port

The system has detected the lack of

CAN message of the port control unit.

Check the CAN bus connection

Miss troll msg

port

The system has detected the lack of

CAN message of the port troll.

Check the CAN bus connection or

the power cord of the unit

controlling the trolling valve

Miss head msg

port

The system has detected the lack of

CAN message of the port control

station.

Check the CAN bus connection

Fw fbk fault port

The system has detected a problem

on the forward gear solenoid valve

(port or single-engine)

Check the connection reliability and

the suitability of the solenoid valve.

Rw fbk fault port

The system has detected a problem

on the reverse gear solenoid valve

(port or single-engine)

Check the connection reliability and

the suitability of the solenoid valve.

Nt fbk fault port

The system has detected a problem

on the neutral solenoid valve, if it is

used (port or single-engine).

Check the connection reliability and

the suitability of the solenoid valve.

Miss acc msg

stbd

The system has detected the lack of

CAN message of the starboard

throttle

Check the CAN bus connection or

the power cord of the unit

controlling the throttle.

Miss disp msg

stbd

The system has detected the lack of

CAN message of the starboard

control unit.

Check the CAN bus connection

Miss troll msg

stbd

The system has detected the lack of

CAN message of the starboard troll.

Check the CAN bus connection or

the power cord of the unit

controlling the trolling valve

Miss head msg

stbd

The system has detected the lack of

CAN message of the starboard

control station.

Check the CAN bus connection

Fw fbk fault stbd

The system has detected a problem

on the forward gear solenoid valve

(starboard)

Check the connection reliability and

the suitability of the solenoid valve.

Rw fbk fault stbd

The system has detected a problem on the

reverse gear solenoid valve (starboard)

Check the connection reliability and

the suitability of the solenoid valve.

Содержание Power A Mark II





































Результаты поиска

Содержание Power A Mark II

Отзывы:

Похожие инструкции для Power A Mark II

Бренды по названию

Популярные бренды

Ultraflex Power A Mark II, Руководство пользователя

Результаты поиска

Содержание Power A Mark II

Отзывы:

Похожие инструкции для Power A Mark II

Бренды по названию

Популярные бренды