background image

Cleaning and maintenance 

5816,0013US / Version 02 

67 

 

11  Cleaning and maintenance  

11.1  Safety  

See also safety notes on page 19, chapter 2.6 "Occupational

safety and special dangers".

General 

 WARNING 

Danger by inappropriate cleaning and 
maintenance! 

Inappropriate cleaning and maintenance can cause 
severe or lethal injuries. 
– All maintenance work must be performed by

specialists or electrical specialists.

– Any possibly present ground fault circuit

interrupter (GFCI) must only be inspected by an
electrician.

– Prior to work, ensure that there is sufficient

assembly space.

– Pay attention to tidiness and cleanness at the

assembly site! Loosely stacked or lying around
components and tools are accident sources.

– After completion of maintenance work, ensure

that all covers are correctly mounted.

– Wear protective helmet.

Personal protective equipment 

The following must be worn during maintenance work: 

Work clothes

Protective gloves

Safety shoes.

Maintenance book 

In barriers where personal traffic cannot be excluded, a 
maintenance book must be maintained. 
In any other barriers, maintenance of a test book is not mandatory. 
However, we recommend keeping a test book in such barriers as 
well, to properly document all maintenance work. 

Traffic H1 Swing Gate Horizontal Barrier

www.TURNSTILES.us | [email protected] | 303-670-1099

Содержание Traffic H1






































































































Отзывы: