manualshive.com logo in svg

Turnstiles Traffic H1, Руководство по эксплуатации


Поделиться
Скачать
background image

Malfunctions 

76 

5816,0013US / Version 02 

 
 

12.3  Warning and interference messages on the display 

The control unit differentiates between events, warnings and 
errors. The corresponding message is displayed. 

Event messages "INFO" 

Event messages inform about events such as "switching to battery 
operation". The barrier continues to run normally. Event messages 
do not influence the outputs of the control unit. 

Warning messages "WARNING" 

Faults that could be reset by the control unit are displayed as 
warnings. Operation of the barrier is not or only briefly impaired.  
If the function "Warning" has been chosen for an output, this output 
is deactivated at pending warnings (fail safe). 

Error messages "ERROR" 

Faults that cannot be reset by the control unit are displayed as 
errors. The barrier is shut down.  
If the function "Error" has been chosen for an output, this output is 
deactivated at pending warnings (fail safe). 
To take the barrier into operation again, the fault must be removed 
by an MHTM MicroDrive service specialist and a reset according to 
chapter 12.4 must be performed.  

For requirements to the MHTM MicroDrive service specialist,

see page 18, chapter 2.4.

NOTE! 
With some messages, the control unit tries to reset 
the cause of the message. If the attempt was 
successful, the message is displayed as 
WARNING. If the attempt failed, the message is 
displayed as ERROR. 

12.3.1 

Event, warning and error messages – Logic control (Control unit) 

Number 

Description 

Possible cause 

Corrective action 

FF01 
WARNING 

Error barrier 
mechanics 

The first closing motion could 
not be performed completely. 

If required, remove obstacle
below the barrier arm.

Check barrier mechanics.

FF02 
WARNING 

Detector 
monitoring signal 

Communication between logic 
control and detector module 
impaired. 

Perform reset. 

 See

page 81, chapter 12.4.

Check plug contacts.

Clean plug contacts with
spirit. Observe ESD
provisions.

Replace the control unit.

Traffic H1 Swing Gate Horizontal Barrier

www.TURNSTILES.us | [email protected] | 303-670-1099

Содержание Traffic H1






































































































Отзывы:

Нет отзывов

Похожие инструкции для Traffic H1

IBM 3708 End-User Reference preview
3708
Бренд: IBM Страницы: 144
Zeagle Razor Service Manual preview
Razor
Бренд: Zeagle Страницы: 37
Harpo BraillePen 12 Quick Start Manual preview
BraillePen 12
Бренд: Harpo Страницы: 35
Hardi HC 6500 Quick Manual preview
HC 6500
Бренд: Hardi Страницы: 2
M-Audio Axiom AIR 25 Service Manual preview
Axiom AIR 25
Бренд: M-Audio Страницы: 26
M Climate Bobbie Installation Instructions Manual preview
Bobbie
Бренд: M Climate Страницы: 12
Eaton S701 Instruction Leaflet preview
S701
Бренд: Eaton Страницы: 8
Balboa BP600 Tech Sheet preview
BP600
Бренд: Balboa Страницы: 23
Balboa VL260 Quick Reference Manual preview
VL260
Бренд: Balboa Страницы: 2
TCi 18055 Manual preview
18055
Бренд: TCi Страницы: 9
Festo CPX-AP-A-16DI-D-M12-5P Operating Instructions Manual preview
CPX-AP-A-16DI-D-M12-5P
Бренд: Festo Страницы: 16
Aeta Audio Systems SCOOP STUDIO Getting Started preview
SCOOP STUDIO
Бренд: Aeta Audio Systems Страницы: 24
Reer MOSAIC MA2 Quick Installation Manual preview
MOSAIC MA2
Бренд: Reer Страницы: 2
M-system R7C-EA16 Instruction Manual preview
R7C-EA16
Бренд: M-system Страницы: 7
SILENTRON SERENYA 2000 Manual preview
SERENYA 2000
Бренд: SILENTRON Страницы: 20
MacroAir Technologies Controller 30 Operation Manual preview
Controller 30
Бренд: MacroAir Technologies Страницы: 32
FAIE 12460 Manual preview
12460
Бренд: FAIE Страницы: 5
GEM 343 eSyDrive Operating Instructions Manual preview
343 eSyDrive
Бренд: GEM Страницы: 31

Бренды по названию

Популярные бренды

Загрузить еще бренды