Turnstiles Traffic H1 Скачать руководство пользователя страница 86

Страница: 86 / 101

Repair

5816,0013US / Version 02

Remove anchor support and barrier
arm

If present, remove anchor support. For this, proceed in the
reverse order as for mounting.



See page 58, chapter 9.3.

Disassemble the barrier arm. For this, proceed in the reverse
order as for mounting.



See page 58, chapter 9.3.

Mount barrier arm

Push the new barrier arm onto the flange.

Attach the barrier arm to the flange using the screws.



Torque wrench: 8 AF



Tightening torque: 12 Nm

Check the swivel range of the
barrier arm

Switch on power supply.

10. Switch the "Service" switch on the control unit. The LED lights

red. The display backlighting flashes.

11. Open and close the barrier manually to check the swivel

range.



Middle left button : Manually open the barrier.



Middle right button

: Manually close the barrier.

Sett close direction

12. If the close direction is incorrect, change the close direction

via the parameter "Close direction".



See separate

document "Description of control units MGC and MGC Pro for
MHTM

MicroDrive barriers", chapter "Close direction".

13. Switch the "Service" switch on the control unit. The LED must

light green.

14. Switch off power supply.

Mount anchor support

15. If present, mount anchor support.



See page 58,

chapter 9.3.

16. Install the rear door of the barrier housing.
17. Install the rear cover of the barrier housing.
18. Lock the lock at the rear door.

Traffic H1 Swing Gate Horizontal Barrier

www.TURNSTILES.us | [email protected] | 303-670-1099

Содержание Traffic H1






































































































Результаты поиска

Содержание Traffic H1

Отзывы:

Похожие инструкции для Traffic H1

Бренды по названию

Популярные бренды

Turnstiles Traffic H1, Руководство по эксплуатации

Результаты поиска

Содержание Traffic H1

Отзывы:

Похожие инструкции для Traffic H1

Бренды по названию

Популярные бренды