TURFCO WIDESPIN 1540 TEC Скачать руководство пользователя страница 18

Страница: 18 / 72

85816

WIDE

SPIN

1540 TEC BROADCAST TOP DRESSER

The Turfco WideSpin 1540 TEC Broadcast Top

Dresser is a truck mounted broadcast top dresser. The

WideSpin 1540 TEC is designed to distribute a uniform

application of properly prepared top dressing material

to the turf. Top dressing is the introduction of new soils

to existing turf.
A conveyor belt carries the top dressing from the

hopper, through an adjustable metering gate, and

into rotating spinner wheels. Top dressing material is

spread at an adjustable width of 3.04 to 9.14 meters

(10’ to 30’ feet) at an operating ground speed up to 8

Km/h (5 mph).

INTENDED USE AND FUNCTION

The WideSpin 1540 TEC is intended to be used for the

application of properly prepared organic top dressing

material. The WideSpin 1540 TEC is NOT intended

to be used for any purpose other than the application

of properly prepared organic top dressing material.

Properly prepared top dressing is organic material with

a controlled moisture content that has been screened

to remove debris, rocks, and excessive sized top

dressing material.
Operation is intended to be at properly prepared

worksites only. The WideSpin 1540 TEC is intended

only to be mounted to trucks having adequate weight,

payload capacity, brakes, and horsepower, and

hydraulic power to safely control the top dresser. The

proper mounting kit must be used to mount the top

dresser to the truck.
The WideSpin 1540 TEC is intended to be used only

when the operator is present at the drivers position

on the truck. The WideSpin 1540 TEC is intended to

be operated only when the truck and top dresser are

moving. The WideSpin 1540 TEC is not intended to be

used when the truck and top dresser are stationary.

The WideSpin 1540 TEC is not intended to be operated

unless it is properly attached to the truck. The 1540

TEC is NOT designed for or intended to accept riders.

● Do Not Use With Unscreened Top Dressing

Material.

● Do Not Use With Non-Organic Top Dressing

Material.

● Do Not Use With Rocks.

Description

● Do Not Allow Anyone To Stand Behind the 1540

TEC When the Spinners Are Operating.

● Do Not Allow Riders On or In the 1540 TEC.
● Do Not Operate On Slopes Over 15º Degrees.
● Do Not Transport or Operate At Ground Speeds

Higher Than 8 Km/h (5 mph).

DESCRIPTION OF THE WIDE

SPIN

1540

LIGHTSPREAD AND HEAVYSPREAD SETTINGS

The WIDE

SPIN

1540 TEC has two settings to control

top dressing material volume rates and the spread

patterns. The LIGHTSPREAD setting is used for

frequent top dressing applications and provides the

widest broadcast pattern with a “light” volume of top

dressing material. The HEAVYSPREAD setting is

used for narrower broadcast pattern with a “heavy”

volume of top dressing material. Changing between

Lightspread and Heavyspread requires repositioning

the spread diverter, changing spinner and conveyor

speed settings, changing the metering gate setting,

and repositioning the spinner wheel vane angles (vane

change required only during very heavy application).

LOCATION AND DESCRIPTION OF THE WIDE

SPIN

1540 TEC BROADCAST TOP DRESSERS MAJOR

COMPONENTS

See Figure 2 and 3 for the location of the major

components of the top dresser. Do not modify the

WideSpin 1540 TEC or its spinner assembly in any

manner. Do not operate the WideSpin 1540 TEC with

damaged or inoperable components.

Manual Tube:

The manual tube

[A]

is located on the

side panel of the hopper. The tube is used to store the

operators manual.

Front and Rear Mounting Points:

The mounting

points

[B]

on the WideSpin 1540 TEC frame are

designed to accept the proper mounting kit for the

speciﬁc truck being used to carry the top dresser.

The mounting kit must be installed to these points for

proper installation.

Lifting Brace:

The detachable lifting brace

[C]

is used

to pick up the WideSpin 1540 TEC during mounting or

removal of the top dresser from the truck. The brace

should be removed during operation. The WideSpin

1540 TEC hopper should always be empty before

lifting the top dresser. The spinner assembly should

be attached to the WideSpin 1540 TEC during lifting to

provide proper balance of the machine.

DESCRIPTION

Содержание WIDESPIN 1540 TEC









































































Результаты поиска

Содержание WIDESPIN 1540 TEC

Отзывы:

Похожие инструкции для WIDESPIN 1540 TEC

Бренды по названию

Популярные бренды

TURFCO WIDESPIN 1540 TEC, Руководство оператора

Результаты поиска

Содержание WIDESPIN 1540 TEC

Отзывы:

Похожие инструкции для WIDESPIN 1540 TEC

Бренды по названию

Популярные бренды