TURFCO WIDESPIN 1540 TEC Скачать руководство пользователя страница 9

Страница: 9 / 72

85816

REMOVING WIDE

SPIN

1540 TEC FROM TRUCK

Always refer to the Assembly and Installation section in

this manual for information and instructions that were

used to install the WideSpin 1540 TEC top dresser to

the truck. Review the steps that were used to install

and connect the top dresser to the truck.

To Avoid Serious Injury,

Never Attempt To Lift the Top Dresser Manually.

Serious Bodily Injury Could Result From Lifting

The Top Dresser By Hand.

The Weight And Balance Of The Machine

Requires Approved Hoists And Lifting Devices.

The Top Dresser weighs 308.4 Kg (680 lbs) when

empty. Ensure that the hoist or lifting device, and

its rigging are rated to safely lift and suspend

the weight of the top dresser. The hopper of the

top dresser must be empty when the machine is

lifted.

Always use the lifting brace to pick up the top dresser.

The lifting brace was designed to protect the hopper

and is located to provide for even balance of the top

dresser when the spinner assembly is installed on the

rear of the top dresser.

Never attempt to install or remove a top dresser that

is ﬁlled with top dressing material.

The hopper must

always be empty. Never attempt to pick up the top

dresser when top dressing is in the hopper.
Disconnect all electrical and hydraulic connections

to the truck before lifting the top dresser.

Refer to the

Operators Manual for the truck to properly reattach

any hydraulic or electrical connections to that part of

the truck.

THE TOP DRESSER AND THE TRUCK

The operator must read and understand the entire

manual for the truck used to carry the WideSpin 1540

TEC top dresser. The operator must be trained in the

operation of the truck and knowledgeable in its safe

operation.

The operator must be aware of the extra

weight placed on the truck when combined with the

top dresser.

The extra weight will effect the handling,

balance, and braking performance of the truck.

TO AVOID SERIOUS INJURY,

Do Not Drive or Operate the Truck and Top

Dresser On Slopes Steeper Than 15º Degrees.

The operator must operate the truck in a safe

manner and know the operating limits of the truck

in relation to the weight, performance, center-of-

gravity, and operating characteristics of the top

dresser.

TO AVOID SERIOUS INJURY,

Read and Understand the Entire Operator’s

Manual Before Operating The WideSpin 1540 TEC

and the Truck.

WARNING

TRUCK REQUIREMENTS

Содержание WIDESPIN 1540 TEC









































































Результаты поиска

Содержание WIDESPIN 1540 TEC

Отзывы:

Похожие инструкции для WIDESPIN 1540 TEC

Бренды по названию

Популярные бренды

TURFCO WIDESPIN 1540 TEC, Руководство оператора

Результаты поиска

Содержание WIDESPIN 1540 TEC

Отзывы:

Похожие инструкции для WIDESPIN 1540 TEC

Бренды по названию

Популярные бренды