TURFCO WIDESPIN 1540 TEC Скачать руководство пользователя страница 22

Страница: 22 / 72

85816

TO AVOID SERIOUS INJURY,

Read and Understand the Entire

Operator’s Manual Before Operating

The WideSpin 1540 TEC and the Truck.

Read and Follow all Safety Decals and Warnings.

TO AVOID SERIOUS INJURY,

Always operate the WideSpin 1540 TEC Top

Dresser Safely and Wear the Appropriate

Personal Safety Equipment.

TO AVOID SERIOUS INJURY,

Keep Hands, Feet, and Clothing Away From

Rotating Spinner Wheels

TO AVOID SERIOUS INJURY,

Do Not Allow Riders In or On The Top Dresser

WIDE

SPIN

1540 TEC OPERATOR POSITION

The proper location for the WideSpin 1540 TEC

operator is seated on the truck seat. Always stop the

trucks engine, set the trucks brakes, and disengage

hydraulic power to the conveyor belt and the spinner

assembly before leaving the trucks seat. Do not stand

behind the WideSpin 1540 TEC when it is operating.

TO AVOID SERIOUS INJURY,

Always Operate the WideSpin 1540 TEC From the

Operators Position at the Trucks Seat.

Always Stop the Trucks Engine, Set the Trucks

Brakes, and Disengage Hydraulic Power to the

WideSpin 1540 TEC Spinners and Conveyor Belt

Before Leaving the Trucks Seat.

DO NOT Allow Anyone To Stand

Behind the 1540 TEC Spinner

Assembly When It Is Operating.

Operation

WIDE

SPIN

1540 TEC OPERATING SPEEDS

When the 1540 TEC top dresser is mounted to the

truck, the

maximum ground speed of the truck

should not exceed 8 Km/h (5 MPH).

Safety concerns

and excessive stress on the truck and the top dresser

will occur if speeds are in excess of 8 Km/h (5 MPH).

TO AVOID SERIOUS INJURY

and To Avoid Damage to the truck and 1540 TEC

top dresser, DO NOT Drive or Operate the 1540

TEC Top Dresser At Speeds Over 8 Km/h (5 MPH).

The ground speed of the truck must be constant to

ensure an even and equal distribution of top dressing

material. The trucks engine speed must be maintained

to ensure a constant and even supply of hydraulic

power. Choose a gear and throttle/governor setting

that will give a maximum ground speed of 8 Km/h (5

MPH). If top dressing speed exceeds 8 Km/h (5 MPH),

poor and uneven top dressing application will result as

well as unsafe operating conditions. For best results,

the 1540 TEC should be moving before the spinner

assembly is engaged.

WIDE

SPIN

1540 TEC MAXIMUM ANGLES OF

OPERATION

Do not drive or operate the truck and WideSpin 1540

TEC on side slopes over 15º degrees. Do not drive

or operate the truck and WideSpin 1540 TEC up or

down slopes over 15º degrees. Do not drive or operate

the truck and WideSpin 1540 TEC with an overﬁlled

or overloaded hopper. Tipping or rolling over of the

machine can occur.

TO AVOID SERIOUS INJURY

and To Avoid Damage to the WideSpin 1540 TEC

Top Dresser and the Truck,

Do Not Operate on Slopes Over 15º Degrees.

WARNING

OPERATION

Содержание WIDESPIN 1540 TEC









































































Результаты поиска

Содержание WIDESPIN 1540 TEC

Отзывы:

TURFCO WIDESPIN 1540 TEC, Руководство оператора, Страница: 22 / 72

Результаты поиска

Содержание WIDESPIN 1540 TEC

Отзывы: