background image

Power

NIM AC85V~132V 0.2A, DC +6V:0.4A,  -6V:0.3A

Counter

Input level

 Current Level -12mA~-36mA:"1"  -4mA~+20mA:"0"

Input

NIM

  Zin = 50Ω

  

 Count frequency More than 500MHz

Input connector  LEMO ERA00250
Channels

 0~7channels (CH7 is preset counter)

Overflow digit

 When count value over the limit send the data "over"

Digit of count

 48bit data(0~281,474,976,710,655 cts)

Timer

 1channel 40bit 1~1,099,511,627,775 μs

Resolution

 0.000001s (1μs)   

Accuracy
Preset time

 1 ~ 1,099,511,627,775 μs

Special

  1channel CH7 Fixed

counter

Preset count

  1 ~ 281,474,976,710,655 cts

Counter

single mode

Count starts by start trigger or "START" command

Mode

Enable to count within preset value one time
Temporarily turn into stop count by stop trigger or "STOP"

command

When disable to preset counter stop and preset timer stop

counting action continues until stop trigger or "STOP"
command

Enable to count or not for all channels and timer
Goes to  count mode by open or "H" level
In count mode LED turn on "green"
In count mode signal out goes "H"
Connect this port to "Gate in TTL" of next unit.
It's possible to activate multiple units simultaneously
Count start input(by TTL rising edge), count stop input
        (by TTL rising edge)
LAN, USB
Enable to upgrade firmware software by communication
NIM 1 UNIT

For the further information, feel free to ask us.

8.Performance and specifications

  0.005%

Gate in TTL

LED in counting
Signal out
In counting

Control input

Number of channel

Number of channel

3739, Kandatsu-machi, Tsuchiura-city, Ibaraki 300-0013, Japan

 TEL: +81-(0)29-832-3031   FAX: +81-(0)29-832-2662

 E-mail : [email protected]

URL : http://www.tsujicon.jp

Communication
Version upgrade
Case

Tsuji-Electronics Co.,Ltd

CH0~CH8
COUNT IN

GND

LEMO

GND

51

NIM LEVEL

NIM LEVEL
RECEIVER

ECL
COUNTER

15/15

Содержание NCT08-02

















Отзывы: