TSI Instruments DustTrak 8535 Скачать руководство пользователя

Страница: 7 / 70

Operation and Maintenance Manual

Safety Information

W A R N I N G

The DustT

rak™ II/DRX aerosol monitor is not rated

for intrinsic safety. The DustTrak™

monitor, with the

Environmental Enclosure, must

NEVER

be operated

under conditions where there is a risk of fire or
explosion

W A R N I N G

Use of components other than those specified by
TSI

may impair the safety features provided by

the equipment.

W A R N I N G

The instrument has been design to be used with
batteries supplied by TSI

DO NOT

use a substitute.

The TSI

charger (P/N 801809) has been designed

to be used with the battery packs supplied by TSI

DO NOT

use a substitute charger to charge TSI

battery packs.

Old batteries must be properly recycled in
accordance with the local environmental regulations.

W A R N I N G

DO NOT

use non-rechargeable batteries in this

instrument. Fire, explosions, or other hazards
may result.

C A U T I O N

The enclosure is designed to be water resistant to
rain or spray. It is not designed to be waterproof
when immersed. Setting it in a pool of water will
result in flooding the inner compartment with water.
This will severely damage both your DustTrak

™ II

DRX

aerosol monitor and battery pack.

DO NOT

set

the Environmental Enclosure in

water

The enclosure has no IP rating or NEMA rating for
dust or water ingress.

Содержание DustTrak 8535







































































Результаты поиска

Содержание DustTrak 8535

Отзывы:

Похожие инструкции для DustTrak 8535

Бренды по названию

Популярные бренды

TSI Instruments DustTrak 8535, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание DustTrak 8535

Отзывы:

Похожие инструкции для DustTrak 8535

Бренды по названию

Популярные бренды