TSI Instruments DustTrak 8535 Скачать руководство пользователя | Manualshive

Страница: 51 / 70

background image

Operation

41

External Pump, the battery pack should be removed from service and
properly recycled in accordance with local environmental regulations.

NOTE

Prior to using the Battery Pack for the first time, a full recharge is
recommended.

Recharging Battery Pack(s) immediately after

use (within one hour maximum) is critical to obtaining optimal
recharge time, battery health, and battery life.

W A R N I N G

The instrument has been designed to be used with
batteries supplied by TSI

®

.

DO NOT

use a substitute.

The TSI

®

charger (P/N 801809) has been designed

to be used with the battery packs supplied by TSI

®

.

DO NOT

use a substitute charger to charge TSI

®

battery packs.

Old batteries must be properly recycled in
accordance with the local environmental regulations.

W A R N I N G

DO NOT

use non-rechargeable batteries in this

instrument. Fire, explosions, or other hazards may
result.

Charging Battery Pack

1. Disconnect the battery pack from the DustTrak

™ II/DRX aerosol

monitor and remove it from the Environmental Enclosure. Take it
to a protected area where it can be charged undisturbed for 8 to 9
hours. Before charging any battery pack, please completely read
the “Battery Charger Owner’s Manual” that was provided along
with your charger.

DO

NOT

attempt to charge Battery Packs

using the Dual Battery Wiring Harness (P/N 801817). The Dual
Battery Wiring Harness is designed to be used to power the 8530,
8531, 8533, 8530EP, or 8533EP and the optional accessories
during instrument operation only.

The information below is

NOT

intended as a substitute to the

charger manual. The charger manual will cover all important
warnings and operating instructions for using the charger. The
steps below will guide you through the battery pack charging
process steps.

«
...
49
50
51
52
53
...
»

Содержание DustTrak 8535







































































Отзывы:

Нет отзывов

Похожие инструкции для DustTrak 8535

Бренд: Eaton Страницы: 4

Бренд: StarTech.com Страницы: 12

MySafe C31MYSAFENVME

Бренд: i-tec Страницы: 40

OptiX OSN 9800 U32 Enhanced Subrack V100

Бренд: Huawei Страницы: 78

Бренд: MODCO Страницы: 7

Бренд: Scuba Capsule Страницы: 17

Бренд: Viz-Art Automation Страницы: 2

Бренд: Fender Страницы: 1

Band-Master Loudspeaker VM 212

Бренд: Fender Страницы: 4

Бренд: Fender Страницы: 8

Бренд: Rittal Страницы: 36

Бренд: Rittal Страницы: 53

PowerVault ME484

Бренд: Dell EMC Страницы: 152

Бренд: Alto Страницы: 12

Opt-X 5WMNT-01C

Бренд: Leviton Страницы: 30

Бренд: CRU Страницы: 2

Data Express QX310

Бренд: CRU Страницы: 4

interlogix 60-928

Бренд: UTC Fire and Security Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды