TSI Instruments DustTrak 8535 Скачать руководство пользователя | Manualshive

Страница: 54 / 70

background image

44

Chapter 3

The Dual Battery Wiring Harness is water-resistant, but

NOT

water-

proof, the cable may fail if subjected to abundant water exposure
including submersion in water.

Zeroing the DustTrak

™

II/DRX

Aerosol Monitor

Always zero the DustTrak

™

II

and

DustTrak

™

DRX

monitor before

beginning a sample. See the instructions in the DustTrak

™

II

or

DustTrak

™

DRX

user

manual for more information. If possible, zero

the instrument under stable ambient temperature conditions (since
variations in temperature will have a small impact upon the
DustTrak

™

monitor readings). If this is not possible (for example,

24-hour outdoor sampling, with wide temperature swings) the
instrument should be kept closed inside the Environmental Enclosure.
The thermal mass of the Enclosure will dampen out the effect of
temperature swings, radiant heat, etc.

In nearly all cases, the temperature impact upon the DustTrak

™ II/

DRX

aerosol

monitor reading is very small in comparison to the

ambient particle concentration.

Setting the Flow Rate for the Respirable Aerosol Inlet

(optional accessory)

The optional Respirable Aerosol Inlet is designed to operate at a
1.7 L/min flow rate to achieve the proper particle cut-off size. When
using a Respirable Aerosol Inlet, the flow rate should be verified
and/or adjusted as described in the DustTrak

™

II

or

DustTrak

™

DRX

user manual to 1.7 L/min.

Locking the Environmental Enclosure

To avoid theft of the DustTrak

™

II/DRX

aerosol

monitor

,

when left

inside the Environmental Enclosure, use a padlock to lock the box.
There are two holes on the front of the box that allow for a standard
padlock to be attached. A padlock is

not

supplied with the

Model 8535.

«
...
52
53
54
55
56
...
»

Содержание DustTrak 8535







































































Отзывы:

Нет отзывов

Похожие инструкции для DustTrak 8535

TotalStorage FAStT EXP700

Бренд: IBM Страницы: 158

Бренд: RaidSonic Страницы: 2

USB 3.0 STORAGE STATION

Бренд: Hamlet Страницы: 12

Бренд: Stands Unique Страницы: 2

Бренд: iStarUSA Страницы: 2

Бренд: Quantum Страницы: 16

Бренд: SICK Страницы: 34

Бренд: American Dryer Страницы: 2

Captair Flow Smart

Бренд: erlab Страницы: 24

Бренд: Dyconn Страницы: 12

Бренд: Sonnet Страницы: 12

Бренд: Apricorn Страницы: 2

Бренд: Natec Страницы: 12

SmartRack SRWF5U36

Бренд: Tripp Lite Страницы: 2

IsoBeam ISO-BEAM-16

Бренд: Ubiquiti Страницы: 4

Бренд: Macally Страницы: 14

Бренд: LaCie Страницы: 41

Бренд: Vantec Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды