Bezique
1
GENEral
1.1
Isolate the electrical and water supplies before
removing the cover.
1.2
Read all of these instructions and retain them
for later use.
1.3
DO nOT take risks with plumbing or electrical
equipment.
1.4
Isolate electrical and water supplies bEFORE
proceeding with the installation.
1.5
The unit must be mounted onto the finished
wall surface (on top of the tiles). DO nOT tile
up to unit after fixing to wall.
1.6
Contact Customer Service
(see back page)
, if
any of the following occur:
a)
If it is intended to operate the shower at
pressures above the maximum or below the
minimum stated.
b)
If the unit shows a distinct change in
performance.
c)
If the shower is frozen.
1.7
If it is intended to operate the shower in areas
of hard water (above 200 ppm temporary
hardness), a scale inhibitor may have to be
fitted. For advice on the Triton Scale Inhibitor,
contact Triton Customer Service.
1.8
The sprayplate and cartridge must be cleaned
regularly with descalent to remove scale and
debris, otherwise restrictions to the flow on
the outlet of the unit will result in higher
temperatures and could also cause the Pressure
Relief Device in unit to operate.
1.9
This product is not suitable for mounting into
steam rooms or steam cubicles.
2
PlumBiNG
2.1
The plumbing installation must comply with
Water Regulations, building Regulations or
any particular regulations as specified by Local
Water Company or Water Undertakers and
should be in accordance with bS 6700.
2.2
The supply pipe must be flushed to clear debris
before connecting to the shower unit.
2.3
DO nOT solder pipes or fittings within 300mm
of the shower appliance, as heat transfer can
damage components.
2.4
DO nOT fit any form of outlet flow control as
the outlet acts as a vent for the heater can.
2.5
DO nOT use excessive force when making
connections to the flexible hose or
showerhead, finger tight is sufficient.
2.6
All plumbing connections MUST be completed
bEFORE making the electrical connections.
3
ElECTriCal
3.1
The installation must comply with bS 7671
‘Requirements for electrical installations’ (IEE
wiring regulations), building regulations or any
particular regulations as specified by the local
Electrical Supply Company.
3.2
This appliance MUST be earthed.
3.3
In accordance with ‘The Plugs and Sockets etc.
(Safety) Regulations 1994’, this appliance is
intended to be permanently connected to the
fixed wiring of the electrical mains system.
3.4
Make sure all electrical connections are tight to
prevent overheating.
3.5
Fuses do not give personal protection against
electric shock.
3.6
To enhance electrical safety
a 30mA residual
current device (RCD) should be installed in all
UK electric and pumped shower circuits. This
may be part of the consumer unit or a separate
unit.
3.7
Switch the unit off immediately at the isolating
switch if water ceases to flow during use.
3.8
Other electrical equipment i.e. extractor fans,
pumps must not be connected to the circuits
within the unit.
3.9
Switch off at isolating switch when not in use.
This is a safety procedure recommended with
all electrical appliances.
3.10
As with all electrical appliances it is
recommended to have the shower and
installation checked at least every two years by
a competent electrician to make sure there is
no deterioration due to age and usage.
P
lease
R
ead
T
his
i
mPoRTanT
s
afeTy
i
nfoRmaTion
u
Products manufactured by Triton are safe and without risk provided they are installed, used and
maintained in good working order in accordance with our instructions and recommendations.
u
WARNING:
Do not operate shower if frozen, or suspected of being frozen. It must thaw
out before using.
u
DO nOT operate the unit if the showerhead or spray hose becomes damaged.
u
DO nOT restrict flow out of the shower by placing showerhead in direct contact with your body.
u
DO nOT operate the shower if water ceases to flow during use or if water has entered inside the
unit because of an incorrectly fitted cover.
