10
TRAXXAS
QUICK START GUIDE
Transmitter Adjustments
Throttle Neutral Position
The trigger is set to 50/50 for equal movement in the throttle direction
and reverse/brake direction. Changing the setting to 70/30 will
increase the range of forward trigger travel and decrease brake trigger
travel.
Note:
You will need to reprogram your electronic speed control to
recognize the 70/30 setting.
Steering Trim
Turn the trim knob to precisely set the
steering neutral point.
Multi-Function Knob
Turn this knob to adjust steering sensitivity.
Turn the knob clockwise to make steering less
sensitive.
ATTENTION: WHEN USING LiPo BATTERY
To prevent over-discharging of LiPo batteries, Low Voltage
Detection must be switched on. To check the status of your model,
turn it on.
If the speed control’s LED is green, Low Voltage Detection
is already activated.
If the LED is red, Low Voltage Detection is not
active.
Follow these steps to turn on Low Voltage Detection:
1. Turn the model on. Make sure the LED on the
speed control is on and red.
2. Press and hold the EZ-Set button for ten
seconds. The LED will turn off and then light
green, and a “rising” musical tone will be
emitted from the motor. Release the button.
3. Low-Voltage Detection is now ACTIVATED.
LiPo batteries are intended only for the most advanced users that
are educated on the risks associated with LiPo battery use.
Never
use LiPo batteries while Low-Voltage Detection is disabled.
To disable Low Voltage Detection when using NiMH batteries, repeat the
steps above. A “falling” musical tone will be emitted from the motor and
the LED will glow red.
Selecting a Throttle Mode: SPORT, RACE, or TRAINING
1. Connect a fully charged battery to the model and turn on your
transmitter.
2. With the model off, press and hold the EZ-Set button until the LED
turns solid green, then solid red and then begins blinking red. It will
blink once, then twice, then three times, then repeat.
One blink = Sport Mode
is the default setting. It allows full forward
and reverse throttle.
Two blinks = Race Mode
removes reverse throttle in case your track
does not allow it.
Three blinks = Training Mode
will slow the model down by 50% to
make it easier for new drivers to control the model.
3. Release the EZ-Set button after the number of blinks for the mode
you wish to select.
Note
:
If you missed the mode you wanted, keep the
EZ-Set button pressed down and the blink cycle will repeat.
4. The LED will blink and then turn solid green (Low-Voltage Detection
ACTIVE) or red (Low-Voltage Detection DISABLED). The model is
ready to drive in the mode you have selected.
Calibrating the Speed Control
The speed control is calibrated at the factory. Follow these steps if you
need to re-calibrate it (set the neutral position).
1. Connect a fully charged battery to the model.
2. Turn on the transmitter (with the throttle at neutral).
3. Press and hold the EZ-Set button (A). The LED will
first turn green and then red. Release the
EZ-Set button.
4. When the LED blinks RED ONCE, pull the
throttle trigger to the full throttle position
and hold it there (B).
5. When the LED blinks RED TWICE, push the
throttle trigger to the full reverse and hold it
there (C).
6. When the LED blinks GREEN ONCE, programming is complete.
The LED will then shine green or red (depending on Low Voltage
Detection setting).
Your Traxxas model is designed with water-resistant features to
protect the electronics in the model (receiver, servos, electronic
speed control). Though highly water resistant, the model should not
be treated as though it is submersible or totally, 100% waterproof.
Water resistance applies only to the installed electronic components.
Running in wet conditions requires additional care and maintenance
to prevent corrosion and maintain proper function. Download the
complete manual for full precautions and maintenance requirements.
Read and understand all precautions before operating your model in
wet conditions. The complete manual for your model can be viewed
and downloaded by following the link on the cover of this manual, or
by scanning the QR code. Please read this entire manual for complete
instructions on the proper use and maintenance of your model.
Gearing
Your model may include an additional pinion gear. This gear is for
maximum-speed running on hard surfaces only. Using the high-speed
gearing for general driving and off-road driving may overheat the
motor, speed control, or battery. For full instructions on installing and
Forward
Neutral
Brake/Reverse
TURN
R
IG
H
T
T
U
R
N
LE
FT
Note: Return the transmitter’s trigger neutral and push up again to
activate reverse throttle
If the model becomes stuck against an object, do not continue to
run the motor. Remove the obstruction before continuing.
Do not push or pull objects with the model.
Green then Red
A
Once Red
B
Twice Red
C