Trane TC*150-301 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 64

background image

46

RT-SVX25C-EN

Maintenance

6. Spray the leaving-airflow side of the coil first; then spray the opposite side of the coil. Allow the

cleaning solution to stand on the coil for five minutes.

7.

Rinse both sides of the coil with cool, clean water.

8. Inspect both sides of the coil; if it still appears to be dirty, repeat Steps 6 and 7.

9. Reinstall all of the components and panels removed in Step 1 and any protective covers

installed in step 2.

10. Restore the unit to it’s operational status and check system operation.

Final Process

For future reference, you may find it helpful to record the unit data requested below in the blanks
provided.

(1) Complete Unit Model Number:

______________________________________________________________________

______________________________________________________________________

(2) Unit Serial Number:

______________________________________________________________________

______________________________________________________________________

(3) Wiring Diagram Numbers (from unit control pane

— schematic(s)

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

— connection(s)

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

«
...
44
45
46
47
48
...
»

Содержание TC*150-301

































































Отзывы:

Нет отзывов

Похожие инструкции для TC*150-301

Бренд: AAF Страницы: 4

Бренд: Daikin Страницы: 12

Super Multi NX FHQ35BVV1B

Бренд: Daikin Страницы: 19

Бренд: CLIVET Страницы: 64

Бренд: Dimplex Страницы: 12

Бренд: Electro-Air Страницы: 15

LM012CI-115P432-1X

Бренд: Lennox Страницы: 44

Бренд: Midea Страницы: 64

Бренд: Olimpia splendid Страницы: 52

Бренд: EINHELL Страницы: 52

Бренд: SPX Cooling Technologies Страницы: 16

Бренд: Carrier Страницы: 22

Бренд: Sonnenkonig Страницы: 64

Бренд: Daikin Страницы: 501

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 30

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды