Trane TC*150-301 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 64

background image

RT-SVX25C-EN

53

Troubleshooting

Note:

Measurements should be made from LED common (ZSM terminal 6 to respective LED
terminal). Refer to the Zone Sensor Module (ZSM) Terminal Identification table at the
beginning of this section.

Programmable & Digital Zone Sensor Test

Testing serial communication voltage

1.

Verify 24 VAC is present between terminals J6-14 & J6-11.

2. Disconnect wires from J6-11 and J6- 12. Measure the voltage between J6-11 and J6-12, should

be about 32 VDC.

3. Reconnect wires to terminals J6-11 and J6-12. Measure voltage again between J6-11 and J6-12,

voltage should flash high and low every 0.5 seconds. The voltage on the low end will measure
about 19 VDC, while the voltage on the high end will measure from approximately 24 to 38 VDC.

4. Verify all modes of operation, by running the unit through all of the steps in the “Test Modes”

section discussed in “Unit Start-Up”.

5. After verifying proper unit operation, exit the test mode. Turn the fan on continuously at the

ZSM, by pressingthe button with the fan symbol. If the fan comes on and runs continuously,
the ZSM is good. If you are not able to turn the fan on, the ZSM is defective.

ReliaTel Refrigeration Module (RTRM) Default Chart

If the RTCI loses input from the buildingmanagement system, the RTRM will control in the default
mode after approximately 15 minutes. If the RTRM loses the Heating and Cooling setpoint input,
the RTRM will control in the default mode instantaneously.

The temperature sensing thermistor in the Zone Sensor Module is the only component required
for the “Default Mode” to operate.

Unit Operation without a Zone Sensor

This procedure is for temporary operation only. The economizer and condenser fan cycling
functions are disabled.

1.

Open and Lock the unit disconnect switch.

2. Remove the Outside Air Sensor (OAS) from the condenser section of unit.

3. Use two (2) wire nuts, to individually cap the wires.

Table 12. System mode and fan selection

Resistance Valves
(Ohms)

Zone Sensor Unit/
Fan Mode

Local Unit Mode

Local Fan Mode

2.32K Off/

Auto

Off

Auto

4.87K Cool/Auto

Cool

Auto

7.68K Auto/Auto

Auto

Auto

10.77K Off/On Off

On

13.32K Cool/On Cool

On

16.13K Auto/On Auto

On

19.48K Heat/Auto

Heat

Auto

27.93K Heat/On

Heat

On

35.0K

Emergency Heat/Auto Emergency Heat

Auto

43.45K

Emergency Heat/On

Emergency Heat

On

Out of Range(Short)

INVALID/Short

Invalid (CV), Auto (VAV) Invalid

Out of Range (Open) INVALID/Open

Invalid (CV), Off (VAV) Invalid

«
...
51
52
53
54
55
...
»

Содержание TC*150-301

































































Отзывы:

Нет отзывов

Похожие инструкции для TC*150-301

Бренд: NANO Страницы: 28

Бренд: GE Страницы: 72

Бренд: Klarstein Страницы: 64

Бренд: Saneo Страницы: 49

Бренд: Valeo Страницы: 60

Бренд: Clatronic Страницы: 62

Бренд: edc Страницы: 46

TAC-09CHSA/XA71

Бренд: TCL Страницы: 45

Бренд: NewAir Страницы: 104

Бренд: Parker Страницы: 48

Бренд: Dimplex Страницы: 10

Бренд: TCL Страницы: 44

Бренд: Oreck Страницы: 46

Бренд: thermital Страницы: 24

Бренд: Rasonic Страницы: 24

Бренд: Zibro Страницы: 2

Бренд: mundoclima Страницы: 38

Бренд: Midea Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды