Trane TC*150-301 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 64

Trane TC*150-301 Скачать руководство пользователя страница 25

RT-SVX25C-EN

25

Installation

1.

Protection devices must be sized according to the electrical data on the nameplate.

2. If the unit is not equipped with an optional factory installed nonfused disconnect switch or

circuit breaker, a field supplied disconnect switch must be installed at or near the unit in
accordance with the National Electrical Code (NEC latest edition).

3. Location of the applicable electrical service entrance is illustrated in

Figure 2, p. 14

and

Figure 4,

p. 15

. Complete the unit’s power wiring connections onto either; the main terminal block HTB1

inside the unit control panel, the factory mounted nonfused disconnect switch (UCD) or circuit
breaker (UCB), or the electric heat terminal block. Refer to the customer connection diagram
that shipped with the unit for specific termination points.

4. Provide proper grounding for the unit in accordance with local and national codes.

Main Unit Power

Optional TBUE Wiring (Through the Base Electrical Option)

1.

Location of the applicable electrical service is illustrated below. Refer to the customer
connection diagram that is shipped with the unit for specific termination points. The
termination points, depending on the customer option selected would be a factory mounted
nonfused disconnect switch (UDC) or circuit breaker (UCB).

2. Provide proper grounding for the unit in accordance with local and national codes.

Field Installed Control Wiring

An overall layout of the various control options available with the required number of conductors
for each control device is illustrated in

Figure 18, “Typical field wiring diagrams for optional

controls (ReliaTel™ only),” on page 31

.

Figure 12. Through the base electrical option

«
...
23
24
25
26
27
...
»

Содержание TC*150-301

































































Отзывы:

Нет отзывов