manualshive.com logo in svg

Trane TC*150-301, Установка, эксплуатация и обслуживание


Поделиться
Скачать
background image

RT-SVX25C-EN

9

General Information

If this circuit is open before the compressor is started, the compressor will not be allowed to 
operate. 

Anytime this circuit is opened for 1 continuous second during compressor operation, the 
compressor for that circuit is immediately turned “Off”. The compressor will not be allowed to 
restart for a minimum of 3 minutes should the contacts close.

If four consecutive open conditions occur during the first three minutes of operation, the 
compressor for that circuit will be locked out, a diagnostic communicated to the remote panel (if 
installed), and a manual reset will be required to restart the compressor.

Phase Monitor

The Phase Monitor is a 3 phase line monitor module that protects against phase loss, phase 
reversal and phase unbalance. It is intended to protect compressors from reverse rotation. It has 
an operating input voltage range of 190-600 VAC, and LED indicators for ON and FAULT. There are 
no field adjustments and the module will automatically reset from a fault condition.

Low Pressure Control ReliaTel Control

When the LPC is opened for 1 continuous second, the compressor for that circuit is turned off 
immediately. The compressor will not be allowed to restart for a minimum of 3 minutes.

If four consecutive open conditions occur during the first three minutes of operation, the 
compressor will be locked out, a diagnostic communicated to ICSTM if applicable, and a manual 
reset will be required to restart the compressor.

Discharge Line Thermostat ReliaTel Control

The high pressure controls and discharge line thermostats are wired in series between the 
compressor outputs on the RTRM and the compressor contactor coils.  If the high pressure control 
switch or discharge line thermostat open, the RTRM senses a lack of current while calling for 
cooling and locks the compressor out.  This is an auto reset lockout.  If the circuit is open three 
consecutive times when the contactor coil should be on, the RTRM sets a manual lockout for that 
compressor.

Power Exhaust Control (Optional)

The power exhaust fan is started whenever the position of the economizer dampers meets or 
exceed the power exhaust setpoint when the indoor fan is on.

The setpoint panel is located in the return air section and is factory set at 25%.

Lead/Lag Control (Dual Circuit Only)

Lead/Lag is a selectable input located on the RTRM. The RTRM is configured from the factory with 
the Lead/Lag control disabled. To activate the Lead/Lag function, simply cut the wire connected to 
J3-8 at the RTRM. When it is activated, each time the designated lead compressor is shut off due 
to the load being satisfied, the lead compressor or refrigeration circuit switches. When the RTRM 
is powered up, i.e. after a power failure, the control will default to the number one circuit 
compressor.

Zone Sensor Module (ZSM) (BAYSENS106A)

This electronic sensor features three system switch settings (Heat, Cool, and Off) and two fan 
settings (On and Auto). It is a manual changeover control with single setpoint. (Cooling Setpoint 
Only)

Zone Sensor Module (ZSM) (BAYSENS108A)

This electronic sensor features four system switch settings (Heat, Cool, Auto, and Off) and two fan 
settings (On and Auto). It is a manual or auto changeover control with dual setpoint capability. It 
can be used with a remote zone temperature sensor BAYSENS017B.

Содержание TC*150-301

































































Отзывы:

Нет отзывов

Похожие инструкции для TC*150-301

easymaxx 04271 Instructions Manual preview
04271
Бренд: easymaxx Страницы: 8
Haier HWS20VCA User Manual preview
HWS20VCA
Бренд: Haier Страницы: 22
Panasonic S-22MU1E5A Service Manual preview
S-22MU1E5A
Бренд: Panasonic Страницы: 53
Friedrich VERT-I-PAK B-SERIES Installation & Operation Manual preview
VERT-I-PAK B-SERIES
Бренд: Friedrich Страницы: 20
MCS Master BC 180 User And Maintenance Book preview
BC 180
Бренд: MCS Master Страницы: 19
Parker SMOG-HOG PSG Owner'S Manual preview
SMOG-HOG PSG
Бренд: Parker Страницы: 36
Aircommand sandpiper Owner'S Manual preview
sandpiper
Бренд: Aircommand Страницы: 22
V-TUF AEROMAX500 Operator'S Manual preview
AEROMAX500
Бренд: V-TUF Страницы: 13
Yoer ARCTICO Manual preview
ARCTICO
Бренд: Yoer Страницы: 36
Zibro S 3526 Datasheet preview
S 3526
Бренд: Zibro Страницы: 2
YILKAR YK 155 MB Installation Instruction preview
YK 155 MB
Бренд: YILKAR Страницы: 42
Daikin RKM46PVMA Service Manual preview
RKM46PVMA
Бренд: Daikin Страницы: 23
dirna Bergstrom 1001207490 Mounting Instructions preview
1001207490
Бренд: dirna Bergstrom Страницы: 72
INVENTOR U5MRSL32(2)-18 User Manual preview
U5MRSL32(2)-18
Бренд: INVENTOR Страницы: 44
ThermoKey JGH1510CZ Technical Manual preview
JGH1510CZ
Бренд: ThermoKey Страницы: 43
FASANO TOOLS FG 700/OZ3.5 Quick Start Manual preview
FG 700/OZ3.5
Бренд: FASANO TOOLS Страницы: 8
Atlas HMA-7000-TC User Manual preview
HMA-7000-TC
Бренд: Atlas Страницы: 8
Heat Controller REG-253H Replacement Parts List preview
REG-253H
Бренд: Heat Controller Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды