Trane TC*150-301 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 64

background image

50

RT-SVX25C-EN

Troubleshooting

Service Failure

1.

If the supply fan proving switch has closed, the unit will not operate (when connected to RTOM),
check the fan motor, belts, and proving switch.

2. Clogged filter switch has closed, check the filters.

Simultaneous Heat and Cool Failure

1.

Emergency Stop is activated.

Method 2

The second method for determining system status is done by checking voltage readings at the
RTRM (J6). The system indication descriptions and the approximate voltages are listed below.

System Failure

Measure the voltage between terminals J6-9 & J6-6.

•

Normal Operation = approximately 32 VDC

•

System Failure = less than 1 VDC, approximately 0.75 VDC

•

Test Mode = voltage alternates between 32 VDC & 0.75 VDC

Heat Failure

Measure the voltage between terminals J6-7 & J6-6.

•

Heat Operating = approximately 32 VDC

•

Heat Off = less than 1 VDC, approximately 0.75 VDC

•

Heating Failure = voltage alternates between 32 VDC & 0.75 VDC

Cool Failure

Measure the voltage between terminals J6-8 & J6-6.

•

Cool Operating = approximately 32 VDC

•

Cool Off = less than 1 VDC, approximately 0.75 VDC

•

Cooling Failure = voltage alternates between 32 VDC & 0.75 VDC

Service Failure

Measure the voltage between terminals J6-10 & J6-6.

•

Clogged Filter = Approximately 32 VDC.

•

Normal = Less than 1 VDC, approximately 0.75 VDC

•

Fan Failure = voltage alternates between 32 VDC & 0.75 VDC.

To use LED’s for quick status information at the unit, purchase a BAYSENS010B ZSM and connect
wires with alligator clamps to terminals 6 through 10. Connect each respective terminal wire (6
through 10) from the Zone Sensor to the unit J6 terminals 6 through 10.

Note:

If the system is equipped with a programmable zone sensor, (BAYSENS019A,
BAYSENS020A or BAYSENS023A), the LED indicators will not function while the
BAYSENS010A is connected.

Resetting Cooling and Heating Lockouts

Cooling Failures and Heating Lockouts are reset in an identical manner.

Method 1 explains resetting the system from the space; Method 2 explains resetting the system at
the unit.

«
...
48
49
50
51
52
...
»

Содержание TC*150-301

































































Отзывы:

Нет отзывов

Похожие инструкции для TC*150-301

Бренд: CLIVET Страницы: 64

Бренд: TruSens Страницы: 32

Бренд: Nortek Страницы: 16

Бренд: SPX Cooling Technologies Страницы: 16

PROFESSIONAL XL INN-560

Бренд: INNOLIVING Страницы: 28

Бренд: Ohyama Страницы: 72

Бренд: Daikin Страницы: 14

50PG08 14 Series

Бренд: Carrier Страницы: 20

Бренд: Xpelair Страницы: 5

Бренд: Daikin Страницы: 100

GWH09RA-K3DNA1B

Бренд: Gree Страницы: 77

Бренд: CLIMAVENETA Страницы: 68

Бренд: Viking Страницы: 2

Бренд: Daikin Страницы: 13

Бренд: Blueridge Страницы: 28

Бренд: ICP Страницы: 12

Бренд: Haier Страницы: 36

Бренд: Haier Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды