Toyota 2002 Sequoia Скачать руководство пользователя страница 99

Страница: 99 / 329

02_SEQUOIA_U (L/O 0108)

2002 MY SEQUOIA_U (OM34418U)

Move seat fully back

CAUTION

A forward

−

facing child restraint sys-

tem should be allowed to be put on

the front passenger seat only when

it is unavoidable. Always move the
seat as far back as possible, be-

cause the force of the deploying

front passenger airbag could cause
death or serious injury to the child.

On vehicles with side airbags, do

not allow the child to lean against
the front door or around the front

door even if the child is seated in

the child restraint system. It is dan-
gerous if the side airbag inflates,

and the impact could cause death
or serious injury to the child.

Same position

Same angle

When installing a child restraint
system in the third seat center

position, adjust both seat cushions

to the same position and align both
seatbacks at the same angle. Other-

wise, the child restraint system can-

not be securely restrained and this
may cause death or serious injuries

in a collision.

Содержание 2002 Sequoia










































































































































































































































































































































Результаты поиска

Содержание 2002 Sequoia

Отзывы:

Бренды по названию

Популярные бренды

Toyota 2002 Sequoia, Руководство пользователя

Результаты поиска

Содержание 2002 Sequoia

Отзывы:

Бренды по названию

Популярные бренды