Toyota 2002 Sequoia Скачать руководство пользователя страница 246

Страница: 246 / 329

02_SEQUOIA_U (L/O 0108)

240

2002 MY SEQUOIA_U (OM34418U)

When restarting out after parking on a

slope:

1. With the transmission in “P” position,

start the engine. Be sure to keep the

brake pedal depressed.

2. Shift into gear.
3. Release the parking brake and brake

pedal and slowly pull or back away
from the wheel blocks. Stop and apply

your brakes.

4. Have someone retrieve the blocks.

CAUTION

Do not exceed 72 km/h (45 mph) or
the posted towing speed limit,

whichever is lower. Because insta-

bility (swaying) of a towing vehicle

−

trailer

combination

usually

in-

creases as the speed increases, ex-

ceeding 72 km/h (45 mph) may
cause loss of control.

Slow down and downshift before

descending steep or long downhill
grades. Do not make sudden down-

shifts.

Avoid holding the brake pedal down
too long or too frequently. This

could cause the brakes to overheat

and result in reduced braking effi-
ciency.

Improving fuel economy is easy—just take

it easy. It will help make your vehicle last

longer, too. Here are some specific tips
on how to save money on both fuel and

repairs:

Keep your tires inflated at the cor-
rect pressure.

Underinflation causes

tire wear and wastes fuel. See page

289 in Section 7

−

2 for instructions.

Do not carry unneeded weight in

your vehicle.

Excess weight puts a

heavier load on the engine, causing

greater fuel consumption.

Avoid lengthy warm

−

up idling.

Once

the engine is running smoothly, begin

driving—but gently. Remember, howev-

er, that on cold winter days this may
take a little longer.

Keep the automatic transmission
overdrive turned on when engine

braking is not required.

Driving with

the overdrive off will reduce the fuel
economy. (For details, see “Automatic

transmission” on page 133 in Section

−

6.)

Accelerate slowly and smoothly.

Avoid jackrabbit starts. Get into high
gear as quickly as possible.

How to save fuel and make

your vehicle last longer

Содержание 2002 Sequoia










































































































































































































































































































































Результаты поиска

Содержание 2002 Sequoia

Отзывы:

Бренды по названию

Популярные бренды

Toyota 2002 Sequoia, Руководство пользователя

Результаты поиска

Содержание 2002 Sequoia

Отзывы:

Бренды по названию

Популярные бренды