Toyota 2002 Sequoia Скачать руководство пользователя страница 37

Страница: 37 / 329

02_SEQUOIA_U (L/O 0108)

2002 MY SEQUOIA_U (OM34418U)

TESTING THE SYSTEM

1. Open all the windows.
2. Set the system as described above.

The side doors and back door should

be locked with the key or wireless re-
mote control transmitter. Be sure to

wait until the indicator light goes off or

starts flashing.

3. Unlock any side door from the inside.

The system should activate the alarm.

4. Stopping the alarm as described above.
5. Repeat this operation for the other

doors and hood. When testing on the
hood, also check that the system is

activated when the battery terminal is

disconnected and then reconnected.

If the system does not work properly,

have it checked by your Toyota dealer.

This indicates that the fuel filler door

is on the left side of your vehicle.

1. To open the fuel filler door, pull the

lever.
When refueling, turn off the engine.

CAUTION

Do not smoke, cause sparks or al-
low open flames when refueling.

The fumes are flammable.

When opening the cap, do not re-
move the cap quickly. In hot weath-

er, fuel under pressure could cause

injury by spraying out of the filler
neck if the cap is suddenly re-

moved.

Fuel tank cap

Содержание 2002 Sequoia










































































































































































































































































































































Результаты поиска

Содержание 2002 Sequoia

Отзывы:

Бренды по названию

Популярные бренды

Toyota 2002 Sequoia, Руководство пользователя

Результаты поиска

Содержание 2002 Sequoia

Отзывы:

Бренды по названию

Популярные бренды