manualshive.com logo in svg

Toyota 2002 Sequoia, Руководство пользователя

Поделиться
Скачать
Toyota 2002 Sequoia Скачать руководство пользователя страница 133

02_SEQUOIA_U (L/O 0108)

127

2002 MY SEQUOIA_U (OM34418U)

(b) Driver’s  Seat  Belt  Reminder  Light

and  Buzzer

This  light  and  buzzer  remind  you  to
buckle  up  the  driver’s  seat  belt.
Once  the  ignition  key  is  turned  to  “ON”  or
“START”,  the  reminder  light  flashes  and

buzzer  come  on  if  the  driver’s  seat  belt

is  not  fastened.  Unless  the  driver  fastens
the  belt,  the  light  keeps  on  flashing  and

the  buzzer  sounds  for  about  4  to  8  se-

conds.

(c) Front  Passenger’s  Seat  Belt  Re-

minder  Light

This  light  reminds  you  to  buckle  up  the

front  passenger’s  seat  belt.
Once  the  ignition  key  is  turned  to  “ON”  or
“START”,  the  reminder  light  flashes  if  a

passenger  sits  in  the  front  passenger  seat
and  does  not  fasten  the  seat  belt.  Howev-

er,  if  a  front  passenger  uses  an  additional

seat  cushion,  the  light  may  not  flash  even
when  the  seat  belt  is  not  buckled  up.
If  luggage  load  is  placed  on  the  front

passenger  seat,  depending  on  its  weight
and  how  it  is  placed  on  the  seat,  built

−

in

sensors  in  the  seat  cushion  may  detect

the  pressure,  causing  the  reminder  light  to
come  on.

(d) Discharge  Warning  Light

This  light  warns  that  the  battery  is  being

discharged.
If  it  comes  on  while  you  are  driving,  there

is  a  problem  somewhere  in  the  charging
system.
The  engine  ignition  will  continue  to  oper-

ate,  however,  until  the  battery  is  dis-
charged.  Turn  off  the  air  conditioning,

blower,  radio,  etc.,  and  drive  directly  to

the  nearest  Toyota  dealer  or  repair  shop.

NOTICE

Do  not  continue  driving  if  the  engine
drive  belt  is  broken  or  loose.

(e) Malfunction  Indicator  Lamp
This  lamp  comes  on  when  the  ignition

key  is  turned  to  the  “ON”  position  and
goes  off  after  the  engine  starts.  This

means  that  the  warning  light  system  is

operating  properly.
If  the  lamp  remains  on  or  the  lamp

comes  on  while  driving,  first  check  the
followings.

!

Empty  fuel  tank
If  the  fuel  tank  is  empty,  refuel  immedi-

ately.

!

Loose  fuel  tank  cap
If  the  fuel  tank  cap  is  loose,  securely

tighten  it.

These  cases  are  temporary  malfunctions.

The  malfunction  indicator  lamp  will  go  off
after  taking  several  driving  trips.
If  the  lamp  will  not  go  off  even  after  the

several  trips,  contact  your  Toyota  dealer
as  soon  as  possible.

If  the  fuel  tank  is  not  empty  or  the  fuel
tank  cap  is  not  loose...

!

There  is  a  problem  somewhere  in  the

engine,  emission  control  system,  elec-
tronic  throttle  control  system,  automatic

transmission  electrical  system  or  warn-

ing  light  system  itself.

Contact  your  Toyota  dealer  as  soon  as

possible  to  service  the  vehicle.
If  the  engine  speed  does  not  increase  with

the  accelerator  pedal  depressed  down  to
about  the  middle  position,  there  may  be

a  problem  somewhere  in  your  electronic

throttle  control  system.
At  this  time,  if  you  depress  the  accelera-

tor  pedal  more  firmly  and  slowly,  you  can

drive  your  vehicle  at  low  speeds.  Have
your  vehicle  checked  by  your  Toyota  deal-

er  as  soon  as  possible.

Содержание 2002 Sequoia










































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды