Toyota 2002 Sequoia Скачать руководство пользователя страница 93

Страница: 93 / 329

02_SEQUOIA_U (L/O 0108)

2002 MY SEQUOIA_U (OM34418U)

1. Run the lap and shoulder belt through

or around the infant seat following the
instructions provided by its manufactur-

er and insert the tab into the buckle

taking care not to twist the belt. Keep
the lap portion of the belt tight.

CAUTION

After inserting the tab, make sure
the tab and buckle are locked and

that the lap and shoulder portions

of the belt are not twisted.

Do not insert coins, clips, etc. in

the buckle as this may prevent you

from properly latching the tab and
buckle.

If the seat belt does not function
normally, it cannot protect your

child from injury. Contact your

Toyota dealer immediately. Do not
use the seat until the seat belt is

fixed.

2. Fully extend the shoulder belt to put it

in the lock mode. When the belt is
then retracted even slightly, it cannot

be extended.

To hold the infant seat securely, make

sure the belt is in the lock mode before

letting the belt retract.

Содержание 2002 Sequoia










































































































































































































































































































































Результаты поиска

Содержание 2002 Sequoia

Отзывы:

Бренды по названию

Популярные бренды

Toyota 2002 Sequoia, Руководство пользователя

Результаты поиска

Содержание 2002 Sequoia

Отзывы:

Бренды по названию

Популярные бренды