Total Gym ELEVATE ENCOMPASS Скачать руководство пользователя страница 6

Страница: 6 / 32

ELEVATE

ENCOMPASS

OWNER’S GUIDE

ELEVATE

ENCOMPASS

OWNER’S GUIDE

LAT BAR ASSEMBLY

After you remove your Encompass from the box and unfold it, it is ready for

you to install the LAT bars. It should look like the picture below.

NOTE:

the

shipping sleeve and the LAT disc nuts must be removed one at a time to

install the LAT bars.

shipping

sleeve

shipping

sleeve

LAT

disc nut

LAT

disc nut

. Open the hardware box and remove the parts necessary to assemble

the LAT bars. The picture below shows tools and parts needed to install

the LAT bars.

1 squeeze

bottle of

loctite

LAT bar disc washers

LAT nut hex wrench

spanner wrench

plastic caps

. Install the left LAT bar completely, then install the right LAT bar to keep

the Encompass stable and safe.

. Loosen the shipping sleeve by holding it from the outside with the

spanner wrench and unscrew the LAT disc nut with the LAT nut hex

wrench (shown below).

NOTE:

The arrows show

the direction to

turn the wrenches

to loosen the left

LAT disc nut. To

loosen the right

LAT disc nut

turn wrenches

the opposite

direction.

. Carefully slide the shipping sleeve out while holding the bushing in. If

the bushing slides out accidentally, slide it back through the hole in the

tower cross arm and into the rail. Discard the shipping sleeve unless you

plan to re-box the unit. Remove the LAT disc nut and set aside for later

use.

shipping

sleeve

outside bushing

LAT

disc nut

inside bushing

ASSEMBLY

Содержание ELEVATE ENCOMPASS

































Результаты поиска

Содержание ELEVATE ENCOMPASS

Отзывы:

Похожие инструкции для ELEVATE ENCOMPASS

Бренды по названию

Популярные бренды

Total Gym ELEVATE ENCOMPASS, Руководство пользователя

Результаты поиска

Содержание ELEVATE ENCOMPASS

Отзывы:

Похожие инструкции для ELEVATE ENCOMPASS

Бренды по названию

Популярные бренды