Toshiba TMPM3V4 Скачать руководство пользователя

Страница: 203 / 544

The followings show the settings in the case that 2 ms width one-shot pulse is output after 3ms by trigger-

ing TBxIN input at the rising edge. (φT1 is selected for counting.)

[Main processing] Capture setting by TBxIN0
Set PORT registers.

TBxEN

← 1

TBxRUN

← X

TBxMOD

← X

TBxFFCR

← X

Set PORT registers.

Allocates corresponding port to TBxIN.
Enables TMRBx operation.
Stops count operation.
Changes source clock to φT1. Fetches a count value into

the TBxCP0 at the rising edge of TBxIN.
Clears TBxFF0 reverse trigger and disables.
Allocates corresponding port to TBxOUT.

Interrupt Set-Enable

← *

Permits to generate interrupts specified by INTCAPx0 inter-

rupt corresponding bit by setting to "1".

TBxRUN

← *

Starts the TMRBx module.

[Processing of INTCAPx0 interrupt service routine] Pulse output setting

TBxRG0

← *

Sets count value. ( 3ms/φT1)

← *

TBxRG1

← *

Sets count value.( (3+2)ms/φT1)

TBxFFCR

← X X − − 1 1 − −

Reverses TBxFF0 if UC consistent with TBxRG0 and

TBxRG1.

TBxIM

← X

Masks except TBxRG1 correspondence interrupt.

Interrupt Set-Enable

← *

Permits to generate interrupt specified by INTTBx interrupt

corresponding bit setting to "1".

[Processing of INTTBx interrupt service routine] Output disable

TBxFFCR

← X

−

Clears TBxFF0 reverse trigger setting.

Interrupt enable clear

← *

Prohibits interrupts specified by INTTBx interrupt correspond-

ing bit by setting to "1".

Note 1: m ; corresponding bit of port
Note 2: X; Don’t care

−; No change

If a delay is not required, TBxFF0 is reversed when data is taken into TBxCP0, and TBxRG1 is set to the

sum of the TBxCP0 value (c) and the one-shot pulse width (p), (c + p), by generating the INTCAPx0 inter-

rupt. TBxRG1 change must be completed before the next match.

TBxFF0 is enabled to reverse when UC matches with TBxRG1, and is disabled by generating the INTTBx

interrupt.

Count clock

(Internal clock)

Timer out

TBxOUT pin

TBxIN pin input

(External trigger pulse)

Match with TBxRG1

(p)

c + p

Enable reverse

INTTBx1

generation

Enable reverse when data

is taken into TBxCP0.

Taking data into the capture register TBxCP0

INTCAPx0

generation

Taking data into the capture

Disable reverse when data

is taken into TBxCP1.

Pulse width

Figure 10-7 One-shot Pulse Output Triggered by an External Pulse (Without Delay)

TMPM3V6/M3V4

Page 181

2019-02-06

Содержание TMPM3V4
































































































































































































































































































































































































































































































































































Результаты поиска

Содержание TMPM3V4

Отзывы:

Похожие инструкции для TMPM3V4

Бренды по названию

Популярные бренды

Toshiba TMPM3V4, Руководство пользователя

Результаты поиска

Содержание TMPM3V4

Отзывы:

Похожие инструкции для TMPM3V4

Бренды по названию

Популярные бренды