Toshiba Satellite A20 Series Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 495

background image

3 Tests and Diagnostics

3.9 Printer Test

3.9 Printer

Test

To execute the Printer Test, select

6

from the DIAGNOSTIC TEST MENU, press

Enter

and

follow the directions on the screen. The Printer Test contains three subtests that test the
output of the printer connected to the computer. The following messages will appear after
selecting the Printer Test from the DIAGNOSTIC TEST MENU. Answer each of the
questions with an appropriate response to execute the test.

NOTE

: A Port Replicator and an IBM compatible printer must be connected to the system

to execute this test.

The following message will appear when the printer test is selected:

channel#1 = XXXXh

channel#2 = XXXXh

channel#3 = XXXXh

Select the channel number (1-3) ?

The printer I/O port address is specified by the XXXXh number. The computer supports
three printer channels. Select the printer channel number, and press

Enter

to execute the

selected subtest.

Subtest 01

Ripple Pattern

This subtest prints characters for codes 20h through 7Eh line-by-line while
shifting one character to the left at the beginning of each new line.

3-24

Satellite A20 Maintenance Manual (960-444)

«
...
134
135
136
137
138
...
»

Содержание Satellite A20 Series
















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Satellite A20 Series

Veriton Hornet N260G

Бренд: Acer Страницы: 22

SST-GD02B Grandia Sereis GD02

Бренд: SilverStone Страницы: 14

Kraus Group MICON 500C

Бренд: RNG Страницы: 50

Бренд: Sharp Страницы: 83

Бренд: Sharp Страницы: 168

Бренд: Toshiba Страницы: 47

SIMATIC VPU200-3104

Бренд: Siemens Страницы: 28

SIMATIC Rack PC IL 40

Бренд: Siemens Страницы: 40

SIMATIC PC BI10

Бренд: Siemens Страницы: 45

SIMATIC RI 45 PIII Series

Бренд: Siemens Страницы: 132

Бренд: Siemens Страницы: 194

SIMATIC IPC627D

Бренд: Siemens Страницы: 186

PCG-VX88 VAIO User Guide (primary manual)

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 14

Бренд: Sony Страницы: 1

PCG-K47 - VAIO - Mobile Pentium 4 3.2 GHz

Бренд: Sony Страницы: 1

PCG-K45 - VAIO - Mobile Pentium 4 3.2 GHz

Бренд: Sony Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды