manualshive.com logo in svg

Toshiba Satellite A20 Series, Руководство по обслуживанию, Страница: 243 / 495

Поделиться
Скачать
Toshiba Satellite A20 Series Скачать руководство пользователя страница 243

4 Replacement Procedures 

4.12  Wireless LAN Card 

3.  Disconnect the wireless LAN antenna cables (black and white) from the wireless 

LAN card using an antenna coaxial cable disconnector. 

 

PJ2200

Wireless LAN card

Wireless LAN antenna cables

(black and white)

Keyboard insulator

(black)

 

Figure 4-20  Removing the Wireless LAN card 

 

4.  Push the wireless LAN card lock latches outward to release the wireless LAN card. It 

will pop up to about a 45-degree angle. 

5.  Disconnect the wireless LAN card from PJ2200 on the system board. Be careful not 

to damage the connector. 

 

4-38 

 

Satellite A20 Maintenance Manual (960-444) 

Содержание Satellite A20 Series
















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов