manualshive.com logo in svg

Toshiba Satellite A20 Series, Руководство по обслуживанию, Страница: 242 / 495

Поделиться
Скачать
Toshiba Satellite A20 Series Скачать руководство пользователя страница 242

4.12  Wireless LAN Card 

4 Replacement Procedures 

4.12  Wireless LAN Card 

Removing the Wireless LAN Card 

To remove the wireless LAN card, make sure the computer is in boot mode and powered off, 
follow the steps below and refer to figures 4-19 and 4-20. 

NOTE:

 The wireless LAN card is an option in some models. This computer supports two 

types of wireless LAN (802.11/b or 802.11a/b combo). In this section, removing/installing 
a wireless LAN card for a/b combo model is described for example. 

CAUTION:  

Do not try to remove the wireless LAN card with the computer turned on.  

You can damage the computer or the wireless LAN card.  Do not touch the connectors on 
the wireless LAN card module on the computer. Debris on the connectors may cause 
wireless LAN card access problems. 

 

1.  Turn up the keyboard insulator. 

2.  (For a/b combo models) 

Remove the following screw securing the wireless LAN card cover. 

• 

M2

×

4 LH STICK screw   

 

×

1 

M2

×

4  LH STICK screw

Wireless LAN card cover

Keyboard insulator

 

Figure 4-19   Removing the Wireless LAN card cover 

Satellite A20 Maintenance Manual (960-444) 

4-37 

Содержание Satellite A20 Series
















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов