manualshive.com logo in svg

Toshiba Satellite A20 Series, Руководство по обслуживанию, Страница: 287 / 495

Поделиться
Скачать
Toshiba Satellite A20 Series Скачать руководство пользователя страница 287

4  Replacement Procedure 

4.30  Fluorescent Lamp 

4  

4.30 Fluorescent Lamp 

This system uses LCD modules from the following suppliers. The procedure for replacing 
the fluorescent lamp is different for each LCD module. Refer to the appropriate procedure. 

Type Part 

No. 

Supplier 

Section 

G33C0000G110 LG.Philips 

4.30.1 

G33C0000L110 Samsung 

4.30.2 

G33C0000Q110 Sharp 

4.30.3 

15.0 
inch 
(XGA) 

G33C0000M110 CHIMEI 

4.30.4 

G33C0000R110 LG.Philips 

4.30.5 

G33C0000N110 Samsung 

4.30.6 

15.0 
inch 
(SXGA+) 

G33C0000P110 Sharp 

4.30.7 

VF2091P01 TOSHIBA 

4.30.8 

VF2057P01 Sharp 

4.30.9 

VF2058P01 Samsung 

4.30.10 

14.1 
inch 
(XGA) 

VF2062P01 L.G. 

Philips 

4.30.11 

 

NOTE

:  - When working with an LCD module, always use a flat, grounded table. 

 

- Handle the backlight unit in the environment without dust, such as on the clean 

bench.  Keep the worktable free from any screws or other material that may 
scratch the LCD surface. 

 

- Use an anti-static or protective sheet. 

 

- When replacing the FL unit, cover with a finger protector or similar to prevent 

soiling or scratching the LCD panel. 

 

- Be careful when handling the lamp. Excessive force may break the lamp. 

 

- Be careful not to soil or deform the lamp reflector. 

 

- Make sure that the power of the LCD module is turned off before connecting or 

disconnecting cables and connectors. 

 

4-82 

Satellite A20  Maintenance Manual (960-444) 

Содержание Satellite A20 Series
















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов