Toshiba Satellite A20 Series Скачать руководство пользователя страница 173

Страница: 173 / 495

3 Tests and Diagnostics

3.24 Floppy Disk Drive Utilities

3.24.2 Operations

1. Selecting

from the DIAGNOSTIC MENU and pressing

Enter

displays the following

message:

[ FDD UTILITIES ]

1 - FORMAT

2 - COPY

3 - DUMP

4 - HDD ID READ

9 - EXIT TO DIAGNOSTICS MENU

2. FORMAT program

(a) Selecting FORMAT displays the following message:

DIAGNOSTICS - FLOPPY DISK FORMAT : VX.XX

Drive number select (1:A, 2:B) ?

(b) Select a drive number to display the following message:

Type select (0:2DD, 3:2HD) ?

Enter

. A message similar to the one

below will be displayed:

Warning : Disk data will be destroyed.

Insert work disk into drive A:

Press any key when ready.

(d) Remove the Diagnostics Disk from the FDD, insert the work disk and press any

key.

The following message will be displayed when the FDD format is executed:

[ FDD TYPE ] : TRACK = XXX

[ FDD TYPE ] : HEAD = X

[ FDD TYPE ] : SECTOR = XX

Format start

[[track, head = XXX X]]

After the floppy disk is formatted, the following message will appear:

Format complete

Another format (1:Yes/2:No) ?

(e) Typing

displays the message from step (c) above. Typing

returns the test to

the DIAGNOSTIC MENU.

3-62

Satellite A20 Maintenance Manual (960-444)

Содержание Satellite A20 Series
















































































































































































































































































































































































































































































































Результаты поиска

Содержание Satellite A20 Series

Отзывы:

Похожие инструкции для Satellite A20 Series

Бренды по названию

Популярные бренды

Toshiba Satellite A20 Series, Руководство по обслуживанию

Результаты поиска

Содержание Satellite A20 Series

Отзывы:

Похожие инструкции для Satellite A20 Series

Бренды по названию

Популярные бренды