manualshive.com logo in svg

Toshiba Satellite A20 Series, Руководство по обслуживанию

Toshiba Satellite A20 Series - современный ноутбук с высокой производительностью. Предлагает бесплатное скачивание Maintenance Manual на manualshive.com, чтобы помочь пользователям с обслуживанием устройства. Получите все необходимые инструкции и советы по уходу за ноутбуком, скачав руководство бесплатно на manualshive.com.

Поделиться
Скачать
background image

2  Troubleshooting Procedures  

2.10  Modem Troubleshooting

 

Procedure 2 

Connector Check and Replacement Check 

The Modem is installed as a modem daughter card (MDC). If the modem malfunctions, there 
may be a bad connection between the MDC and the sound board, or the sound board and the 
system board. Or the MDC, the sound board, the system board or their connectors might be 
damaged. 

Disassemble the computer following the steps described in Chapter 4, 

Replacement Procedures

 

and perform the following checks: 

Check 1  Make sure the MDC is firmly connected to PJ3010 on the sound board, and the RJ-11 

Jack (modem jack) is firmly connected to MDC JP1. 

 

RJ-11
(Modem
jack)

Sound board

PJ3010

JP1

MDC

System board

PJ9600

PJ9601

PJ9511

PJ9510

 

 

                  If a connector is disconnected, connect it firmly and repeat Procedure 1.  If the 

Modem is still not functioning properly, perform Check 2. 

Check 2  The RJ-11 jack may be defective or damaged.  Replace the RJ-11 jack with a new one 

following the steps in Chapter 4, 

Replacement Procedures

.  If the modem is still not 

functioning properly, perform Check 3. 

Check 3  The MDC may be defective or damaged.  Replace it with a new one following the 

steps in Chapter 4, 

Replacement Procedures

.  If the modem is still not functioning 

properly, perform Check 4. 

Check 4  The sound board or system board may be defective or damaged.  Replace the sound 

board or system board with a new one following the steps in Chapter 4, 

Replacement 

Procedures

.  

  

2-48 

Satellite A20 Maintenance Manual (960-444) 

Содержание Satellite A20 Series
















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Satellite A20 Series

IBM PC 300GL Type 6267 Technical Information Manual preview
PC 300GL Type 6267
Бренд: IBM Страницы: 58
Radio Shack TRS-80 Color Computer 2 User Manual preview
TRS-80 Color Computer 2
Бренд: Radio Shack Страницы: 44
PROAIM P-WKST-01 Assembly Manual preview
P-WKST-01
Бренд: PROAIM Страницы: 3
eMachines A26EV17F (French) Manuel D'Utilisation preview
A26EV17F
Бренд: eMachines Страницы: 46
Lanoptik MV60 User Manual preview
MV60
Бренд: Lanoptik Страницы: 16
BE QUIET! Dark Base 700 User Manual preview
Dark Base 700
Бренд: BE QUIET! Страницы: 48
InHand InBox300 Series User Manual preview
InBox300 Series
Бренд: InHand Страницы: 28
D-Link DWL-P1012 - Power Injector - 185 Watt User Manual preview
DWL-P1012 - Power Injector - 185 Watt
Бренд: D-Link Страницы: 51
Moxa Technologies DA-681C Series Quick Installation Manual preview
DA-681C Series
Бренд: Moxa Technologies Страницы: 6
Kogan ERGOLUX ELRIPLGDKBA User Manual preview
ERGOLUX ELRIPLGDKBA
Бренд: Kogan Страницы: 16
Kogan ERGOLUX ELDUALMTWHA User Manual preview
ERGOLUX ELDUALMTWHA
Бренд: Kogan Страницы: 20
AOpen miniPC Duo MP965-DR User Manual preview
miniPC Duo MP965-DR
Бренд: AOpen Страницы: 56
Shuttle SW580R8 Series User Manual preview
SW580R8 Series
Бренд: Shuttle Страницы: 28
Metro DataVac AccessPoint Operator'S Manual preview
AccessPoint
Бренд: Metro DataVac Страницы: 110
S&T Kontron KBox B-201 User Manual preview
Kontron KBox B-201
Бренд: S&T Страницы: 65
Mitsubishi Apricot MS540 Owner'S Handbook Manual preview
Apricot MS540
Бренд: Mitsubishi Страницы: 77
VarTech Systems VTPC150VHBR User Manual preview
VTPC150VHBR
Бренд: VarTech Systems Страницы: 8
Veriton N4670GT Service Manual preview
N4670GT
Бренд: Veriton Страницы: 74

Бренды по названию

Популярные бренды

Загрузить еще бренды