Toshiba Satellite A20 Series Скачать руководство пользователя страница 183

Страница: 183 / 495

3 Tests and Diagnostics

3.26 SETUP

Moving Within the SETUP Menu and Changing Values

1. Press

and

to move between the two columns. Press

PgDn

and

PgUp

to move

between the two pages. Press

↑

and

↓

to move between items in a column.

2. Press either the

space bar

to change the value.

Accepting Changes and Exiting the SETUP Window

1. Press

End

to accept the changes you made.

The following message is displayed:

Are you sure? (Y/N)

The changes you made will cause the system to reboot.

2. To make other changes, press

. Repeat the steps above.

3. To accept the changes, press

NOTE:

You can press

Esc

to quit at any time without saving changes. SETUP asks you

to confirm that you do not want to save your changes toward User.

The Factory Preset Configuration

When you access SETUP, the current configuration is displayed.

1. To show the factory preset configuration, press

Home

2. Press

End

and then press

to accept the factory preset settings.

NOTE:

When you execute the default setting, the following settings are not changed:

HDD

Mode

Password

Write Policy in the CPU Cache

3-72

Satellite A20 Maintenance Manual (960-444)

Содержание Satellite A20 Series
















































































































































































































































































































































































































































































































Результаты поиска

Содержание Satellite A20 Series

Отзывы:

Похожие инструкции для Satellite A20 Series

Бренды по названию

Популярные бренды

Toshiba Satellite A20 Series, Руководство по обслуживанию

Результаты поиска

Содержание Satellite A20 Series

Отзывы:

Похожие инструкции для Satellite A20 Series

Бренды по названию

Популярные бренды