Toshiba Satellite A20 Series Скачать руководство пользователя страница 193 | Manualshive

Страница: 193 / 495

background image

3 Tests and Diagnostics

3.26 SETUP

11. PCI Bus

This item displays the interrupt level for the Card Bus. It is for information only and
cannot be changed.

PCI BUS = IRQ11

12. Legacy Emulation.

(a) USB keyboard/Mouse Legacy Emulation.

Use this option to enable or disable USB KB/Mouse Legacy Emulation. If
your operating system does not support USB, you can still use a USB mouse
and keyboard by setting the

USB KB/Mouse Legacy Emulation

item to

Enabled

.

Enabled

USB Legacy Support can be used. (Default)

Disabled

USB Legacy Support cannot be used.

(b) USB-FDD Legacy Emulation.

Use this option to enable or disable USB-FDD Legacy Emulation.

Enabled

USB Legacy Support can be used. (Default)

Disabled

USB Legacy Support cannot be used.

13. PC Card

This option sets the PC Card Controller mode. This option can be changed when
“Device Config.” is set to “All Devices”.

Auto-Selected

Use this setting for all PC Cards when OS supports

Plug&Play. (Default)

PCI Compatible

Use this setting for PCIC compatible PC card.

CardBus/16-bit

Use this setting when CardBus does not work properly in

Auto-Selected”, or PC card supports 16-bit.

14. Drives I/O

This option displays the address and interrupt level for hard disk drive, CD/DVD-
ROM drive and PC card. It is for information only and cannot be changed.

(a) Built-in HDD

Primary IDE (1F0H/IRQ14)

The Built-in HDD is ready for use.

No Drive

The

Built-in

HDD

is

not

installed.

3-82

Satellite A20 Maintenance Manual (960-444)

«
...
191
192
193
194
195
...
»

Содержание Satellite A20 Series
















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Satellite A20 Series

Бренд: Challenger Страницы: 96

Бренд: Displays2go Страницы: 2

Бренд: Everex Страницы: 47

Compute Stick STK1A32SC

Бренд: Intel Страницы: 11

Бренд: Avalue Technology Страницы: 12

Бренд: Global Specialties Страницы: 44

Бренд: PRESONUS Страницы: 8

Бренд: Gateway Страницы: 134

5694 - GT - 4 GB RAM

Бренд: Gateway Страницы: 126

Ferrari 1000 Series

Бренд: Acer Страницы: 123

Бренд: Acer Страницы: 112

Rosemount TankRadar SCC 5320

Бренд: Emerson Страницы: 4

Бренд: Emerson Страницы: 108

Бренд: Acer Страницы: 48

Бренд: Acer Страницы: 68

5535-5050 - Aspire

Бренд: Acer Страницы: 11

Бренд: Acer Страницы: 24

Бренд: Acer Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды