manualshive.com logo in svg

Toshiba Satellite A20 Series, Руководство по обслуживанию, Страница: 174 / 495

Поделиться
Скачать
Toshiba Satellite A20 Series Скачать руководство пользователя страница 174

3.24  Floppy Disk Drive Utilities 

3   Tests and Diagnostics 

3. COPY program 

(a)  When COPY is selected, the following message appears: 

FLOPPY DISK FORMAT & COPY : VX.XX 

Type select (0:2DD,3:2HD) ? 

(b)  Selecting a media/drive type number will display a message similar to the one 

below: 

Insert source disk into drive A: 

Press any key when ready. 

(c)  Remove the Diagnostics Disk from the FDD, insert the source disk and press any 

key. The following message will appear, indicating the program has started. 

[ FD TYPE ] : TRACK 

 

= XXX 

[ FD TYPE ] : HEAD

   

= X 

[ FD TYPE ] : SECTOR = XX 
Copy start 

[[ track,head = XXX X ]] 

(d)  Remove the source disk from the FDD, insert a formatted work disk and press 

any key. The [[ track, head = XXX X ]] message will appear and start copying to 
the target disk. When the amount of data is too large to be copied in one 
operation, the message from step (b) displays again. After the floppy disk has 
been copied, the following message will appear: 

Copy complete 

Another copy (1:Yes/2:No) ? 

(e)  To copy another disk, type 

1

 and the message from step (a) displays again. 

Entering 

2

 returns the test program to the DIAGNOSTIC MENU. 

 

Satellite A20 Maintenance Manual (960-444) 

 

3-63

 

Содержание Satellite A20 Series
















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов