Toshiba RAS-10JAVP-E Скачать руководство пользователя страница 75

Страница: 75 / 87

– 75 –

No.

Part name

Drift fan

Procedures

1) Stop operation of the air conditioner and turn off

its main power supply.

2) Follow to the procedure in the item

3) Remove two fixing screws at the left side of the

end plate of the heat exchanger, and remove
two fixing screws of the bearing base.

4) Lift up slightly the left side of the heat ex-

changer to remove the bearing base.

5) Loosen the set screw of the drift fan at dis-

charge port.

6) Remove two fixing screws of the motor band

(Right) to remove the motor band (Right).

Remarks

7) Slide the fan motor outward to remove it.

8) Remove the fixing screws at the lower right side

of the heat exchanger.

9) Remove the heat exchanger from two hanged

parts of the motor band (Left) while sliding it
rightward.

10) Lift up the left side of the heat exchanger

toward you to remove the drift fan.

Motor band (Right)

Fixing screws

Hanged parts

Rear side of mains

Fixing screws
(Bearing base)

Heat exchanger

Top view of the set

(Without panel)

Bearing
base

Fixing
screws

Set screw

Drift fan

Содержание RAS-10JAVP-E
























































































Результаты поиска

Содержание RAS-10JAVP-E

Отзывы:

Похожие инструкции для RAS-10JAVP-E

Бренды по названию

Популярные бренды

Toshiba RAS-10JAVP-E, Руководство по обслуживанию

Результаты поиска

Содержание RAS-10JAVP-E

Отзывы:

Похожие инструкции для RAS-10JAVP-E

Бренды по названию

Популярные бренды