Toshiba RAS-10JAVP-E Скачать руководство пользователя страница 76

Страница: 76 / 87

– 76 –

No.

Part name

Drift fan

Procedures

• Caution at reassembly

a) At assembling work of the bearing base, check that

the drain pipe is surely incorporated
in the rear plate.
(Otherwise, water
leak is caused.)

Remarks

b) To incorporate the fan motor, remove the fan motor

rubber (at shaft core side), incorporate the motor
into the position in the following figure, and then
install the fan motor.

• Install the drift fan so that the right end of the 1st

joint from the right of the draft fan is set keeping
70.5mm from wall of rear plate of the main unit.

• Holding the set screw, install the drift fan so that

U-groove of the fan motor comes to the mounting
hole of the set screw.

• Install the fan motor for service work so that the

center D-letter cut part comes to the set screw
mounting hole position.

• Perform positioning of the fan motor as follows:

c) For incorporation of the motor band (Right), follow

to the above procedure b), incorporate two hanging
hooks of the motor band (Right) into the main unit,
and then follow to the reverse procedure in 7).

Drain pipe

U groove

Center D-letter cut part

Arrange mark of the concave
round hole (or circle mark)
correctly with mark of
the motor band (Right).

Mark

Concave round
hole or circle mark

Hanging hooks
(Two positions)

Motor band
(Right)

70.5mm

Joint

Содержание RAS-10JAVP-E
























































































Результаты поиска

Содержание RAS-10JAVP-E

Отзывы:

Бренды по названию

Популярные бренды

Toshiba RAS-10JAVP-E, Руководство по обслуживанию

Результаты поиска

Содержание RAS-10JAVP-E

Отзывы:

Бренды по названию

Популярные бренды