Toshiba RAS-10JAVP-E Скачать руководство пользователя страница 77

Страница: 77 / 87

– 77 –

No.

Part name

Electric dust
collector

Procedures

1) Remove the front panel. (

Front panel)

2) Remove a fixing screw and a connector.

3) Remove the minus ion generator.

4) Remove the electric dust collector vertically to

the heat exchanger.

<Caution at installation>

1) Arrange screw hole on the end plate correctly to

screw hole on the electric dust collector, insert
the fixing hooks at the rear side of the dust collector
into the heat exchanger, and then fix it with a screw.

2) Install the minus

ion generator.

3) Perform wiring of the

lead wire as follows:

Remarks

11-2. How to replace the parts of electric dust collector

(Be sure to pull off the power plug before work.)

Main frame
unit

Upper frame
collector

High-
pressure unit

1) Follow to the procedure in item

2) Remove the dust collector unit.

(Lift up it once, and then draw out it.)

1) Remove the dust collector unit.

2) Remove the fixing hooks at 6 positions, and

separate the unit into upper frame and collector.

1) Follow to the procedure in item

2) Remove two fixing hooks at upper and lower

sides of the cover to remove the cover.

3) Remove thick red and black Faston lead wires

and the connector attached to the main frame.

4) Remove the earth cover at the rear side of the

electric dust collector, and then remove the thin
black Faston wire.

5) As shown in the right figure, widen outward the

rib at the right side of the main frame and
remove the hooks of the high-pressure unit to
remove the high-pressure unit.

<Caution at installation>

1) Perform cabling as shown in the right figure.

Connector

Pipe

Screw
(1 pc.)

Screw (1 pc.)

Minus ion generator

Fixing hooks for
heat exchanger

Hook

Main frame

Dust collector unit

Hook

Collector

Hooks

Upper frame

Hook

Boss for
positioning

Main frame unit

Hook

Cover

Black

Connector

Black
(thin)

Red

Содержание RAS-10JAVP-E
























































































Результаты поиска

Содержание RAS-10JAVP-E

Отзывы:

Бренды по названию

Популярные бренды

Toshiba RAS-10JAVP-E, Руководство по обслуживанию

Результаты поиска

Содержание RAS-10JAVP-E

Отзывы:

Бренды по названию

Популярные бренды