Toshiba RAS-10JAVP-E Скачать руководство пользователя страница 36

Страница: 36 / 87

– 36 –

8-3. Temporary Operation

• Temporary Auto operation, existence of Auto

Restart, and Temporary Cooling operation can be
set by the RESET button of the indoor controller.

RESET button

Control

OFF

→

Temporary Auto operation start

After pushing button

Auto Restart control select

for 3 seconds

After pushing button

Temporary Cooling

for 10 seconds

operation start

Fig. 8-3-1

Table 8-3-1

8-3-1. Temporary Auto Operation

• When the RESET button is pushed, the Auto

operation with set temperature fixed at 25°C starts.
Controlling is same as that of Auto operation by
the remote controller.

• When the RESET button is pushed again, the

operation stops.

• During Temporary Auto operation, operation by the

remote controller is accepted.

• Using the Auto Restart function, the Temporary

Auto operation starts when power failure is reset.

8-3-2. Temporary Cooling Operation

• When the RESET operation button keeps pushed

for 10 seconds, Cooling operation of which com-
pressor motor speed and the indoor fan speed are
fixed starts.

Compressor motor speed :

13 : 30 rps

Indoor fan speed : Low

• When the TRESET operation button is pushed

again, the operation stops.

• Auto Restart function is unavailable.

Содержание RAS-10JAVP-E
























































































Результаты поиска

Содержание RAS-10JAVP-E

Отзывы:

Бренды по названию

Популярные бренды

Toshiba RAS-10JAVP-E, Руководство по обслуживанию

Результаты поиска

Содержание RAS-10JAVP-E

Отзывы:

Бренды по названию

Популярные бренды