Toshiba RAS-10JAVP-E Скачать руководство пользователя страница 81

Страница: 81 / 87

– 81 –

No.

;

Reactor

Part name

Control board
assembly

Procedure

1) Disconnect lead wires and connectors con-

nected from the control board assembly to other
parts.

1. Lead wires Lead wires Lead wires Lead

wires

• Connection with terminal block :

3 wires (Black, White, Orange)

• Connection with compressor :

Remove the connector (3P).

• Connection with reactor :

Remove the relay connectors from P07, 08
(2P, White) and P12, 13 (2P, Yellow).

2. Connectors

CN300 : Outdoor fan (3P, White)

CN301 : Outdoor fan position detection

(5P, White)

CN701 : 4 valve (3P, Yellow)

CN600 : TE sensor (2P, White)

CN601 : TD sensor (3P, White)

CN603 : TS sensor (3P, White)

CN602 : TO sensor (2P, White)

CN500 : Case thermo. (2P, White)

CN703 : Pulse modulating valve (6P, White)

2) Remove the control board assembly from P.C.

board base.

1. Main control board assembly side

• Remove two claws of P.C. board base, and

remove upward the heat sink with hands.

• Remove three screws fixing the heat sink

and main control board assembly side, and
replace the board with a new one.

1) Perform work of item 1 of

, and

2) Remove fixed screws fixing to the bottom plate.

(ST1TØ4 x 10 3 pcs.)

3) Remove fixed screws fixing to the heat

exchanger. (ST1TØ4 x 10 2 pcs.)

4) Remove fixed screw fixing to the valve mounting

plate. (ST1TØ4 x 10 1 pc.)

Rear cabinet

Remarks

CN300, CN301 and CN701, etc.
at the control board assembly
side are connectors with locks.
Therefore, remove the connector
while pushing the part indicated
by an arrow.

When mounting a new board,
check that the board is correctly
set in the groove of base holder of
P.C. board base.

P.C. board base

P.C. board

CN701

CN500

CN703

CN602

CN301

CN300

CN603

CN601

CN600

Содержание RAS-10JAVP-E
























































































Результаты поиска

Содержание RAS-10JAVP-E

Отзывы:

Бренды по названию

Популярные бренды

Toshiba RAS-10JAVP-E, Руководство по обслуживанию

Результаты поиска

Содержание RAS-10JAVP-E

Отзывы:

Бренды по названию

Популярные бренды