Toshiba RAS-10JAVP-E Скачать руководство пользователя страница 73

Страница: 73 / 87

– 73 –

11. HOW TO REPLACE THE MAIN PARTS

11-1. Indoor Unit

No.

Part name

Front panel

Procedures

1) Stop operation of the air conditioner and turn off

its main power supply.

2) Push “PUSH” part under the front panel and

remove hooks of the front panel from the
installation board.

3) Remove the front panel fixing screws (2 pcs.)

while opening the suction grille.

4) Push the electric parts box with the right thumb

while drawing the both sides of the front panel
toward you.

<How to mount the front panel>

1) Push three center positions and two lower

center positions of the discharge port, and then
hang the hanging hooks (4 cs.) at the top side
of the front panel to the rear plate.

2) Tighten two screws.

• Incomplete hanging or incomplete pushing

may cause a dewdrops or generation of a
beep sound.

Remarks

Electric parts
box assembly

Fixing
screw

Installation
board

Front panel

Hanging hooks at the top side

(4 positions)

Push

Fixing screw

Screw

Drain
guide

Lead wire
cover

TC sensor

Horizontal
louver

1) Follow to the procedure in the above item

2) Remove the drain guide.

3) Remove the electric dust collector. (*)

4) Remove screw attached to the end plate of the

heat exchanger.

5) Remove the lead wire cover, and remove

connector (5P) for the fan motor and connector
(5P) for the louver motor from the microcom-
puter assembly.

6) Remove a fixing screw of the electric parts base

and draw out it toward you.

7) Pull out TC sensor from sensor holder of the

heat exchanger.

8) As shown in the right figure, treat the lead wire

surely after replacement of the parts.
(Otherwise, water leak is caused.)

* For removal/mounting of the electric dust

collector, follow to the item

, How to replace

the electric dust collector.

1) Remove shaft of the horizontal louver from the

rear plate. (First remove the left shaft, and then
remove other shafts while sliding the horizontal
louver leftward.)

Содержание RAS-10JAVP-E
























































































Результаты поиска

Содержание RAS-10JAVP-E

Отзывы:

Похожие инструкции для RAS-10JAVP-E

Бренды по названию

Популярные бренды

Toshiba RAS-10JAVP-E, Руководство по обслуживанию

Результаты поиска

Содержание RAS-10JAVP-E

Отзывы:

Похожие инструкции для RAS-10JAVP-E

Бренды по названию

Популярные бренды