manualshive.com logo in svg

Toshiba RAS-10JAVP-E, Руководство по обслуживанию

Поделиться
Скачать
Toshiba RAS-10JAVP-E Скачать руководство пользователя страница 43

– 43 –

WARNING

• Never modify this unit by removing any of the safety guards or by-pass any of the safety interlock

switches.

• Do not install in a place which cannot bear the weight of the unit. Personal injury and property damage

can result if the unit falls.

• Before doing any electrical work, attach an approved plug to the power supply cord and make sure the

equipment is grounded.

• Appliance shall be installed in accordance with national wiring regulations.

If you detect any damage, do not install the unit. Contact your Toshiba dealer immediately.

WARNING

• Exposure of unit to water or other moisture before installation may result in an electrical short. Do not

store in a wet basement or expose to rain or water.

• After unpacking the unit, examine it carefully for any damage.

• Do not install in a place that can increase the vibration of the unit.  Do not install in a place that can

amplify the noise level of the unit or where noise or discharged air might disturb neighbors.

• To avoid personal injury, be careful when handling parts with sharp edges.

• Please read the installation manual carefully before installing the unit.  It contains further important

instructions necessary for proper installation.

Содержание RAS-10JAVP-E
























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды