Toshiba MAGNIA 510D Скачать руководство пользователя страница 118

Страница: 118 / 185

Hardware Diagnostics

Hardware Diagnostics Program

118

❖

10. CD-ROM TEST checks the computer's CD-ROM functions

Insert the Magnia 510D Software and Documentation CD-ROM for this test.

- 01. Sequential Address Read subtest is a sequential reading of one block unit of all

the logical addresses.

- 02. Random Address Read subtest reads data at random addresses.

For the error log information, refer to Log Utilities for the SCSI HDD TEST.

❖

11. SAF-TE TEST checks the SAF-TE function and the status LED of the hard disk
drives.

- 01. SAF-TE test detects the SAF-TE controller and checks the operation by flashing

the LED for each hard disk drive.

The test detects the SAF-TE controller first and shows the connecting destination of
the detected SAF-TE controller (host number, SCSI ID, and channel number) with
model name. For example:

--HT-ID----CH--VENDOR-PRODUCT-------FAN-PS--SLOT

XX XX XX XXXXX XXXX XX XX XX

After detecting the SAF-TE controller, the following message displays:

SAF-TE LED Steady ON (Faulty Flag)

Hit any key

Check that all LEDs of the hard disk drives are lit orange. Then press

Enter

The following message displays:

SAF-TE LED Blinking (Rebuilding Flag)

Hit any key

Check that all LEDs for the hard disk drives are flashing orange. Then press

Enter

The following message displays:

SAF-TE LED Steady ON (Rebuild Interrupted) Hit any key

Check that all LEDs for the hard disk drives are lit orange. Then press

Enter

The following message displays:

SAF-TE LED Blinking (Rebuilding Flag)

Hit any key

Check that all LEDs of the hard disk drives are flashing orange. Then press

Enter

The following message displays:

SAF-TE LED Reset (No Error Flag)

Hit any key

Check that all LEDs of the hard disk drives are off. Then press

Enter

Содержание MAGNIA 510D


























































































































































































Результаты поиска

Содержание MAGNIA 510D

Отзывы:

Toshiba MAGNIA 510D, Руководство пользователя, Страница: 118 / 185

Результаты поиска

Содержание MAGNIA 510D

Отзывы: