Toshiba MAGNIA 510D страница 81 Скачать руководство пользователя

Страница: 81 / 185

System Configuration Setup

Setup

❖

AC Back Function

❖

Modem Use IRQ - Specifies an interruption (IRQ3 ~ IRQ7) for a AC97 CODEC-
controlled modem. Specify IRQ4.

❖

Modem Ring On/Wake-On-LAN

(At the time of this publication, this system does not

support Wake-On-LAN.)

❖

PME Event Wake Up - Determines if the server will wake up if a PME even occurs.

❖

RTC Alarm Power On - Specifies the date and time when the server is automatically
started.

Memory

Restarts the system based on the previous
setting (Soft Off or Full On)

Soft-Off
(default)

Restarts the system when the power button is
pressed

Full-On

Restarts the system when the power is turned
on.

Disable
(default)

Disables this function

Enabled
(default)

Enables the PME Event Wake Up function

Disabled

Disables the PME Event Wake Up function

Enabled
(default)

Enables this function. If enabled, specify a
date and time.

Disabled

Disables this function

Содержание MAGNIA 510D


























































































































































































Результаты поиска

Содержание MAGNIA 510D

Отзывы:

Похожие инструкции для MAGNIA 510D

Бренды по названию

Популярные бренды

Toshiba MAGNIA 510D, Руководство пользователя

Результаты поиска

Содержание MAGNIA 510D

Отзывы:

Похожие инструкции для MAGNIA 510D

Бренды по названию

Популярные бренды