Toshiba EtherNet/IP Modbus IPE002Z, Руководство по эксплуатации функций

Страница: 9 / 89

E6581741
- 8 -
Title
Communi
cation No.
Function Description
Factory
setting
c021 C021 Scanner output 1 address (*3)
0: -
1: fd01 (Status information 1)
2: fd00 (Output frequency, 0.01Hz)
3:
fd03
(Output current, 0.01%)
4:
fd05
(Output voltage, 0.01%)
5:
fc91
(Alarm information)
6:
fd22
(PID feedback value, 0.01Hz)
7:
fd06
(Input terminal board status)
8: fd07 (Output terminal status)
9: fe36 (VIB input, 0.01%)
10: fe35 (VIA input, 0.01%)
11:
fe37
(VIC input, 0.01%)
12:
fd04
(Input voltage (DC detection), 0.01%)
13:
fd16
(Estimated speed 0.01Hz)
14:
fd18
(Torque, 0.01%)
15: -
16: -
17: -
18: -
19:
f880
(Free notes)
20:
fd29
(Input power, 0.01kW)
21:
fd30
(Output power, 0.01kW)
22: fe14 (Cumulative operation time, hour)
23: fe40 (FM terminal output monitor, 0.01%)
24: -
25:
fd20
(Torque current, 0.01%)
26:
fd23
(Motor overload factor, 0.01%)
27:
fd24
(Drive overload factor, 0.01%)
28:
fd25
(PBR overload factor, %)
29:
fd26
(Motor load factor, %)
30: fd27 (Drive load factor, %)
31: fe56 (Pulse train input, pps)
32: fe70 (Drive rated current, 0.1A)
33:
fe76
(Input Watt-hour, 0.1kWh 10 f749 )
34:
fe77
(Output Watt-hour, 0.1kWh 10
f749
)
35:
fd83
(IGBT temperature, degree C)
1
c022
C022 Scanner output 2 address (*3)
0-35 (Same as
c021
) 2
c023
C023 Scanner output 3 address (*3)
0-35 (Same as
c021
) 0
c024 C024 Scanner output 4 address (*3)
0-35 (Same as c021 )
0
c025
C025 Scanner output 5 address (*3)
0-35 (Same as
c021
) 0
c026 C026 Scanner output 6 address (*3)
0-35 (Same as
c021
)
0
c081-
c096
C081-
C096
Device Name 1-16 (*4)
16 characters
The device name is required if the card uses
DHCP to obtain its IP Address.
Refer to " 3.2.1 Device name (c081-c096) for the
details.
0,0,0,0,
0,0,0,0
c100
C100
Communication error
detection delay time
0.0 - 100.0 sec.
0.0
c101
C101
Inverter operation at the
communication loss action
0: Stop and controlled by
cmod
,
fmod
1: Operation continue
2: Deceleration stop
3: Coast stop
4: Network error stop (
err8
trip)
5: Preset speed operation (by c102 setting)
4
c102 C102
Preset speed operation
selection
0: None
1 to 15: Preset speed
0
c103 C103
Communication time-out
condition selection
0: Disconnection detection
1: When communication mode enable (Both
cmod and fmod are set CANopen or
communication option) only
2: 1 + Driving operation
0
(*3): This parameter is effective by reset. Please reset (power supply reset or f899 = 1 ) after changing a set point.
(*4): (
V[R
) does not work for this parameter.