Toshiba e-STUDIO160 Скачать руководство пользователя

Страница: 203 / 239

December 2002 TOSHIBA TEC

4 - 81

e-STUDIO160/200/250 TROUBLESHOOTING

(23) Jittering image

Step

Cause/Defect area

Registration roller

Pinch roller

Heat roller

Process unit (Drum gear,

cleaner paddle drive gear,

toner recovery auger drive

gear)

Process unit (Drum)

Carriage operation

Scanner

Drum drive system

Main drive gear assembly

Measures

If normal, perform step 2 to 4. Otherwise per-

form step 5 and after.

Clean roller surface with alcohol, or replace

roller.

Re-mount or replace spring.

Check heat roller drive system.

Replace gear or roller if necessary.

Clean gears.

Replace process unit or drum.

Replace slider sheet.

Replace feet.

Adjust the tension.

Check carriage drive system.

Fix mirror properly.

Re-install wire and timing belt with jig.

Clean or replace gears if they have stain or

scratches.

Re-install main drive gear assembly with jig.

Check items

Toner image paper on drum nor-

mal?

Registration roller dirty?

Pinch roller spring out of place?

Heat roller rotation defective?

Foreign matter or toner on gears?

Large scratch on drum?

Slider sheet defective?

Any abnormalities on carriage

feet?

Tension of timing belt inappropri-

ate?

Carriage drive system malfunc-

tioning?

Mirror loosely mounted?

Wire and timing belt tension

proper?

Drum drive system malfunction-

ing?

Main drive gear assembly improp-

erly mounted?

Feeding direction

Содержание e-STUDIO160















































































































































































































































Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды

Toshiba e-STUDIO160, Руководство по обслуживанию

Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды