Toshiba e-STUDIO160 Скачать руководство пользователя

Страница: 206 / 239

December 2002 TOSHIBA TEC

5 - 3

e-STUDIO160/200/250 UPDATING THE FIRMWARE

Fig 5-2-3

(5) Turn on the power.

Downloading of the main data starts.

The downloading status is displayed on the LCD of the copier as follows:

• Data is being downloaded from the ROM on the recovery PWA to the DRAM on the main PWA.

The number of displayed squares (

) increases.

Main PWA

Main recovery PWA

CN10

(4) Insert the main recovery PWA into CN10 of the main PWA, with the ROM mounting side facing down.

• Data is being stored in the flash ROM from the DRAM.

The number of displayed squares (

) decreases.

• Downloading is completed.

All dots are blinking.

Note:

It takes approx. 5 minutes to download the main data.

Number of downloaded data

1: Main data

( 2: Scanner data)

05-02-03

Содержание e-STUDIO160















































































































































































































































Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды

Toshiba e-STUDIO160, Руководство по обслуживанию

Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды