Toshiba e-STUDIO160 Скачать руководство пользователя

Страница: 103 / 239

December 2002 TOSHIBA TEC

2 - 1

e-STUDIO160/200/250 PREVENTIVE MAINTENANCE

2. PREVENTIVE MAINTENANCE (PM)

2.1

Maintenance Performed Every 81,000 (e-STUDIO160/200 Series) and

99,000 Copies (e-STUDIO250 Series)

(1) Preparation

Ask user about the current machine condition and note them down.

Before starting maintenance, make some sample copies and save them.

Turn OFF the power, and be sure to unplug the copier.

(2) Perform preventive maintenance using the following checklist and the illustrations. Refer to the Ser-

vice Manual and Parts List if necessary.

(3) When the maintenance is finished, plug in the copier, turn ON the power, and make a few copies to

confirm that the copier is working properly.

2.2 Preventive Maintenance Check List

Symbols used in the check list

Date

User’s name

Serial No.

Inspector’s

name

Remarks

Cleaning

Cleaning with

alcohol

Cleaning with

soft pad, cloth or

vacuum cleaner

Lubrication

GR Grease

(X5-6020)

White grease

(Molykote HP-300)

FL Floil (GE-334C)

Silicon oil

Alvania No. 2

Replacing

27K

Every 27,000 copies

33K

Every 33,000 copies

81K

Every 81,000 copies

99K

Every 99,000 copies

135K Every 135,000 copies

165K Every 165,000 copies

Replace if deformed

or damaged

Operation check

After cleaning or

replacing, check

for no abnormality

Notes:

1. Perform cleaning and apply lubrication every 81,000 copies for e-STUDIO160/200 series and

99,000 copies for e-STUDIO250 series.

2. <P-I> under "Remarks" indicates page and item number in the Parts List.

3. Replacement cycle of the parts of the feeding section depends on the number of papers fed

from each paper source.

4. Values under "Replacement" indicates the replacement cycle for the e-STUDIO160/200 series

e-STUDIO250 series.

5. Do not put oil on the rollers and belts when lubricating them.

6. Replace the parts with the life of 27,000 copies (e-STUDIO160/200 series) and 33,000 copies

(e-STUDIO250 series) listed in the check list.

7. Replace the heat roller (metallic gold or dark green) and PM kit (FU-KIT-1600N and FU-KIT-

2500N) at every 135,000 copies (e-STUDIO160/200 series) and 165,000 copies (e-STUDIO250

series).

Содержание e-STUDIO160















































































































































































































































Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды

Toshiba e-STUDIO160, Руководство по обслуживанию

Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды