Toshiba e-STUDIO160 Скачать руководство пользователя

Страница: 192 / 239

e-STUDIO160/200/250 TROUBLESHOOTING

4 - 70

December 2002 TOSHIBA TEC

Step

Cause/Defect area

Paper

Transfer charger

Registration roller

Pinch roller

HVPS (transfer/separation

charger/guide bias)

Measures

Reinsert paper with reverse side up or change

paper.

Change paper.

Avoid storing paper in damp place.

Clean transfer charger case.

Clean transfer charger wire.

Clean roller, or replace defective clutch-related

parts.

Re-mount or replace spring.

Adjust output from HVPS, or replace defec-

tive HVPS.

Replace process unit, laser scanner unit, or

the transfer unit.

Check items

Paper in cassette or LCF curled?

Paper in cassette or LCF damp?

Transfer charger case dirty?

Transfer charger wire dirty?

Registration roller malfunctioning?

Pinch roller spring out of place?

High-voltage output defective?

If problem persists after measures

are applied, or there is no prob-

lem found in above check, follow

procedure described in right col-

umn.

(12) Poor image transfer

Feeding direction

Содержание e-STUDIO160















































































































































































































































Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды

Toshiba e-STUDIO160, Руководство по обслуживанию

Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды