Toshiba e-STUDIO160 Скачать руководство пользователя

Страница: 184 / 239

e-STUDIO160/200/250 TROUBLESHOOTING

4 - 62

December 2002 TOSHIBA TEC

Step

Cause/Defect area

Process unit installation

Process unit

(main charger)

HVPS (main charger)

Measures

Re-install process unit securely.

Clean terminals.

Replace the process unit or charger wire.

Adjust output from HVPS, or replace defec-

tive HVPS.

Replace the process unit, laser scanner unit,

HVPS, or main PWA.

Check items

Process unit securely installed?

Charger wire terminals/grid termi-

nals (process unit) and corre-

sponding terminals (main body)

stained?

Is there any disconnection in the

charger wire?

High-voltage output defective?

If problem persists after measures

are applied, or there is no prob-

lem found in above check, follow

procedure described in right col-

umn.

Feeding direction

(4) Solid copy

Содержание e-STUDIO160















































































































































































































































Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды

Toshiba e-STUDIO160, Руководство по обслуживанию

Результаты поиска

Содержание e-STUDIO160

Отзывы:

Похожие инструкции для e-STUDIO160

Бренды по названию

Популярные бренды